forked from juribeparada/MMDVM_HS
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Config.h
116 lines (93 loc) · 3.33 KB
/
Config.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
/*
* Copyright (C) 2017,2018,2019,2020 by Andy Uribe CA6JAU
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#if !defined(CONFIG_H)
#define CONFIG_H
// Select one board (STM32F103 based boards)
// 1) ZUMspot RPi or ZUMspot USB:
// #define ZUMSPOT_ADF7021
// 2) Libre Kit board or any homebrew hotspot with modified RF7021SE and Blue Pill STM32F103:
#define LIBRE_KIT_ADF7021
// 3) MMDVM_HS_Hat revisions 1.1, 1.2 and 1.4 (DB9MAT & DF2ET)
// #define MMDVM_HS_HAT_REV12
// 4) MMDVM_HS_Dual_Hat revisions 1.0 (DB9MAT & DF2ET & DO7EN)
// #define MMDVM_HS_DUAL_HAT_REV10
// 5) Nano hotSPOT (BI7JTA)
// #define NANO_HOTSPOT
// 6) NanoDV NPi or USB revisions 1.0 (BG4TGO & BG5HHP)
// #define NANO_DV_REV10
// 7) D2RG MMDVM_HS RPi (BG3MDO, VE2GZI, CA6JAU)
// #define D2RG_MMDVM_HS
// 8) BridgeCom SkyBridge HotSpot
// #define SKYBRIDGE_HS
// Enable ADF7021 support:
#define ENABLE_ADF7021
// Enable full duplex support with dual ADF7021 (valid for homebrew hotspots only):
// #define DUPLEX
// TCXO of the ADF7021
// For 14.7456 MHz:
#define ADF7021_14_7456
// For 12.2880 MHz:
// #define ADF7021_12_2880
// Configure receiver gain for ADF7021
// AGC automatic, default settings:
#define AD7021_GAIN_AUTO
// AGC automatic with high LNA linearity:
// #define AD7021_GAIN_AUTO_LIN
// AGC OFF, lowest gain:
// #define AD7021_GAIN_LOW
// AGC OFF, highest gain:
// #define AD7021_GAIN_HIGH
// Host communication selection:
// #define STM32_USART1_HOST
#define STM32_USB_HOST
// #define STM32_I2C_HOST
// I2C host address:
#define I2C_ADDR 0x22
// Enable mode detection:
#define ENABLE_SCAN_MODE
// Send RSSI value:
// #define SEND_RSSI_DATA
// Enable Nextion LCD serial port repeater on USART2 (ZUMspot Libre Kit and ZUMspot RPi):
#define SERIAL_REPEATER
#define SERIAL_REPEATER_BAUD 9600
// Enable Nextion LCD serial port repeater on USART1 (Do not use with STM32_USART1_HOST enabled):
// #define SERIAL_REPEATER_USART1
// Enable P25 Wide modulation:
// #define ENABLE_P25_WIDE
// Disable mode LEDs blink during scan mode:
// #define QUIET_MODE_LEDS
// Engage a constant or descreet Service LED mode once repeater is running
// #define CONSTANT_SRV_LED
// #define CONSTANT_SRV_LED_INVERTED
// #define DISCREET_SRV_LED
// #define DISCREET_SRV_LED_INVERTED
// Use the YSF and P25 LEDs for NXDN
// #define USE_ALTERNATE_NXDN_LEDS
// Use the D-Star and DMR LEDs for POCSAG
// #define USE_ALTERNATE_POCSAG_LEDS
// Enable for RPi 3B+, USB mode
#define LONG_USB_RESET
// Enable modem debug messages
#define ENABLE_DEBUG
// Disable frequency bands check
// #define DISABLE_FREQ_CHECK
// Disable frequency restrictions (satellite, ISS, etc)
// #define DISABLE_FREQ_BAN
// Enable UDID feature
// #define ENABLE_UDID
#endif