GitHub - dzungpv/dnckatsw00x: Zigbee light switch with dim support base on chip cc2530

Ligh Switch base on Samplight Z-Stack Home 1.2.2a for CC2530, 2538 SOC

I use this board as light switch/high load switch, for a long distant normal one could not reach and I can choose any high current relay and contactor for very high load. Support up to 4 relay and button control.

The module include an external antena can reach 200m distant: Z-0001 by WEBEE.

Where to buy:

Include 2 module, kit and programing/debug tool: Kit
Only the module: Module

Setup the relay/Contactor, and button:

Connect relay 1 control pin with P1.0, relay 2 with P1.1, relay 3 with P1.2, relay 4 with P1.3,
Connect your button 1 with P0.0, button 2 with P0.1, button 3 with P0.4, button 4 with P0.5

Prebuild hex:

Version with 1 relay and button ready to flash with your tool download it here: dnckatsw00x.hex and use channel 15

Support gateway/hub/software:

Please check:

Zigbee2Mqtt

Home Assistant

Build it from scratch:

Step 1:

Download Z-Stack Home 1.2.2a it is free but require to register Z-Stack Home

Step 2:

Edit file C:\Texas Instruments\Z-Stack Home 1.2.2a.44539\Projects\zstack\HomeAutomation\SampleLight\Source\zcl_samplelight_data.c with those infor:

const uint8 zclSampleLight_ManufacturerName[] = { 6, 'D','N','C','K','A','T' };
const uint8 zclSampleLight_ModelId[] = { 11, 'D','N','C','K','A','T','_','S','0','0','X' };// X is number from 1 to 4 defend on your usage
const uint8 zclSampleLight_DateCode[] = { 16, '2','0','1','8','0','6','2','3',' ',' ',' ',' ',' ',' ',' ',' ' };

Step 3:

Add more code and definition below Add report state code to zclSampleLight_LcdDisplayUpdate: Report for 1 relay verions

  //report state
  zclSampleLightSeqNumState++;
  zclReportCmd_t rptcmd;
  rptcmd.numAttr = 1;
  rptcmd.attrList[0].attrID = ATTRID_ON_OFF;
  rptcmd.attrList[0].dataType = ZCL_DATATYPE_BOOLEAN;
  rptcmd.attrList[0].attrData = (void *)(&zclSampleLight_OnOff);

  // Set destination address to indirect
  zclSampleLight_DstAddr.addrMode = (afAddrMode_t)Addr16Bit;
  zclSampleLight_DstAddr.addr.shortAddr = 0;
  zclSampleLight_DstAddr.endPoint=1;
  zcl_SendReportCmd(SAMPLELIGHT_ENDPOINT,&zclSampleLight_DstAddr, ZCL_CLUSTER_ID_GEN_ON_OFF, &rptcmd, ZCL_FRAME_SERVER_CLIENT_DIR, true, zclSampleLightSeqNumState );

For 2 relay verions just add more on/off variable zclSampleLight_OnOff1, register 1 more endpoint: SAMPLELIGHT_ENDPOINT+ 1 in zclSampleLight_Init()

Add more Endpoint SimpleDescription, you can add more with 3 and 4 button version

SimpleDescriptionFormat_t zclSampleLight_SimpleDesc[2] =
{
{
  SAMPLELIGHT_ENDPOINT,                  //  int Endpoint;
  ZCL_HA_PROFILE_ID,                     //  uint16 AppProfId;
#ifdef ZCL_LEVEL_CTRL
  ZCL_HA_DEVICEID_DIMMABLE_LIGHT,        //  uint16 AppDeviceId;
#else
  ZCL_HA_DEVICEID_ON_OFF_LIGHT,          //  uint16 AppDeviceId;
#endif
  SAMPLELIGHT_DEVICE_VERSION,            //  int   AppDevVer:4;
  SAMPLELIGHT_FLAGS,                     //  int   AppFlags:4;
  ZCLSAMPLELIGHT_MAX_INCLUSTERS,         //  byte  AppNumInClusters;
  (cId_t *)zclSampleLight_InClusterList, //  byte *pAppInClusterList;
  ZCLSAMPLELIGHT_MAX_OUTCLUSTERS,        //  byte  AppNumInClusters;
  (cId_t *)zclSampleLight_OutClusterList //  byte *pAppInClusterList;
  },
  {
  SAMPLELIGHT_ENDPOINT,                  //  int Endpoint;
  ZCL_HA_PROFILE_ID,                     //  uint16 AppProfId;
#ifdef ZCL_LEVEL_CTRL
  ZCL_HA_DEVICEID_DIMMABLE_LIGHT,        //  uint16 AppDeviceId;
#else
  ZCL_HA_DEVICEID_ON_OFF_LIGHT,          //  uint16 AppDeviceId;
#endif
  SAMPLELIGHT_DEVICE_VERSION,            //  int   AppDevVer:4;
  SAMPLELIGHT_FLAGS,                     //  int   AppFlags:4;
  ZCLSAMPLELIGHT_MAX_INCLUSTERS,         //  byte  AppNumInClusters;
  (cId_t *)zclSampleLight_InClusterList, //  byte *pAppInClusterList;
  ZCLSAMPLELIGHT_MAX_OUTCLUSTERS,        //  byte  AppNumInClusters;
  (cId_t *)zclSampleLight_OutClusterList //  byte *pAppInClusterList;
  },
  {
  SAMPLELIGHT_ENDPOINT+1,                  //  int Endpoint;
  ZCL_HA_PROFILE_ID,                     //  uint16 AppProfId;
#ifdef ZCL_LEVEL_CTRL
  ZCL_HA_DEVICEID_DIMMABLE_LIGHT,        //  uint16 AppDeviceId;
#else
  ZCL_HA_DEVICEID_ON_OFF_LIGHT,          //  uint16 AppDeviceId;
#endif
  SAMPLELIGHT_DEVICE_VERSION,            //  int   AppDevVer:4;
  SAMPLELIGHT_FLAGS,                     //  int   AppFlags:4;
  ZCLSAMPLELIGHT_MAX_INCLUSTERS,         //  byte  AppNumInClusters;
  (cId_t *)zclSampleLight_InClusterList, //  byte *pAppInClusterList;
  ZCLSAMPLELIGHT_MAX_OUTCLUSTERS,        //  byte  AppNumInClusters;
  (cId_t *)zclSampleLight_OutClusterList //  byte *pAppInClusterList;
  }
};

Add to zclSampleLight_Init()

  // This app is part of the Home Automation Profile
  zclHA_Init( &zclSampleLight_SimpleDesc[0] ); //button 1
  zclHA_Init( &zclSampleLight_SimpleDesc[1] ); //button 2

  // Register the ZCL General Cluster Library callback functions
  zclGeneral_RegisterCmdCallbacks( SAMPLELIGHT_ENDPOINT, &zclSampleLight_CmdCallbacks );//button 1
  zclGeneral_RegisterCmdCallbacks( SAMPLELIGHT_ENDPOINT+1, &zclSampleLight_CmdCallbacks );//button 2

  // Register the application's attribute list
  zcl_registerAttrList( SAMPLELIGHT_ENDPOINT, zclSampleLight_NumAttributes, zclSampleLight_Attrs );//button 1
  zcl_registerAttrList( SAMPLELIGHT_ENDPOINT+1, zclSampleLight_NumAttributes, zclSampleLight_Attrs );//button 2

  // Register the Application to receive the unprocessed Foundation command/response messages
  zcl_registerForMsg( zclSampleLight_TaskID );

#ifdef ZCL_DISCOVER
  // Register the application's command list
  zcl_registerCmdList( SAMPLELIGHT_ENDPOINT, zclCmdsArraySize, zclSampleLight_Cmds );//button 1
  zcl_registerCmdList( SAMPLELIGHT_ENDPOINT+1, zclCmdsArraySize, zclSampleLight_Cmds );//button 1
#endif

Add report code

  //report state for button 1
  zclSampleLightSeqNumState++;
  zclReportCmd_t rptcmd;
  rptcmd.numAttr = 1;
  rptcmd.attrList[0].attrID = ATTRID_ON_OFF;
  rptcmd.attrList[0].dataType = ZCL_DATATYPE_BOOLEAN;
  rptcmd.attrList[0].attrData = (void *)(&zclSampleLight_OnOff);

  // Set destination address to indirect
  zclSampleLight_DstAddr.addrMode = (afAddrMode_t)Addr16Bit;
  zclSampleLight_DstAddr.addr.shortAddr = 0;
  zclSampleLight_DstAddr.endPoint=1;
  zcl_SendReportCmd(SAMPLELIGHT_ENDPOINT,&zclSampleLight_DstAddr, ZCL_CLUSTER_ID_GEN_ON_OFF, &rptcmd, ZCL_FRAME_SERVER_CLIENT_DIR, true, zclSampleLightSeqNumState );
  //report state for button 2
  zclSampleLightSeqNumState++;
  zclReportCmd_t rptcmd;
  rptcmd.numAttr = 1;
  rptcmd.attrList[0].attrID = ATTRID_ON_OFF;
  rptcmd.attrList[0].dataType = ZCL_DATATYPE_BOOLEAN;
  rptcmd.attrList[0].attrData = (void *)(&zclSampleLight_OnOff1);

  // Set destination address to indirect
  zclSampleLight_DstAddr.addrMode = (afAddrMode_t)Addr16Bit;
  zclSampleLight_DstAddr.addr.shortAddr = 0;
  zclSampleLight_DstAddr.endPoint=1;
  zcl_SendReportCmd(SAMPLELIGHT_ENDPOINT+1,&zclSampleLight_DstAddr, ZCL_CLUSTER_ID_GEN_ON_OFF, &rptcmd, ZCL_FRAME_SERVER_CLIENT_DIR, true, zclSampleLightSeqNumState );

Handle incomming command in zclSampleLight_OnOffCB:

static void zclSampleLight_OnOffCB( uint8 cmd )
{
afIncomingMSGPacket_t *pPtr = zcl_getRawAFMsg();
if (pPtr->endPoint == SAMPLELIGHT_ENDPOINT) //button 1
{
...
}
else if (pPtr->endPoint == SAMPLELIGHT_ENDPOINT+1) //button 2
{
...
}
else if (pPtr->endPoint == SAMPLELIGHT_ENDPOINT+2) //button 3
{
...
}
else if (pPtr->endPoint == SAMPLELIGHT_ENDPOINT+3) //button 4
{
...
}
}

You can see 2 project i learn from here https://github.com/presslab-us/ZigBee_WDHA-12 and https://github.com/presslab-us/ZigBee_OpenEVSE

Step 4:

Disable ZCL_EZMODE and HOLD_AUTO_START build tag by add 'x' before each, and finally build and download to your module

Configuration for Home Assistant

1 button

  - platform: "mqtt"
    name: DNCKAT_S001
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state }}"
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/set"

2 button

# zigbee 2G L      
  - platform: "mqtt"
    name: "DNCKAT_S002 Left"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_left }}"
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/left/set"
# zigbee 2G R   
  - platform: "mqtt"
    name: "DNCKAT_S002 Right"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_right }}"
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/right/set"

3 button

# zigbee 3G L      
  - platform: "mqtt"
    name: "DNCKAT_S003 Left"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_left }}";
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/left/set"
 # zigbee 3G Center      
  - platform: "mqtt"
    name: "DNCKAT_S003 Center"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_center }}";
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/center/set"   
# zigbee 3G R   
  - platform: "mqtt"
    name: "DNCKAT_S003 Right"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_right }}";
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/right/set"

4 button

 #zigbee 4G TL      
  - platform: "mqtt"
    name: "DNCKAT_S004 Top Left"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_top_left }}"
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/top_left/set"
# zigbee 4G TR   
  - platform: "mqtt"
    name: "DNCKAT_S004 Top Right"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_top_right }}";
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/top_right/set"  
 # zigbee 4G BL      
  - platform: "mqtt"
    name: "DNCKAT_S004 Bottom Left"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_bot_left }}";
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/bot_left/set"
# zigbee 4G BR   
  - platform: "mqtt"
    name: "DNCKAT_S004 Bottom Right"
    state_topic: "zigbee2mqtt/FRIENDLY_NAME"
    availability_topic: "zigbee2mqtt/bridge/state"
    payload_off: "OFF"
    payload_on: "ON"
    value_template: "{{ value_json.state_bot_right }}";
    command_topic: "zigbee2mqtt/FRIENDLY_NAME/bot_right/set"

Dimmer version 1 gang (DC only):

Build it from scratch:

Follow all step above with additional: In Step 2 change

const uint8 zclSampleLight_ModelId[] = { 11, 'D','N','C','K','A','T','_','D','0','0','1' };

Step 4: Enable ZCL_LEVEL_CTRL by remove x from xZCL_LEVEL_CTRL buil tag And wire led output as dimmable source.

Name		Name	Last commit message	Last commit date
Latest commit History 12 Commits
LICENSE		LICENSE
README.md		README.md
_config.yml		_config.yml
dnckatsw001.patch		dnckatsw001.patch
dnckatsw00x.hex		dnckatsw00x.hex
dnckatsw00x.jpg		dnckatsw00x.jpg

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Repository files navigation

Ligh Switch base on Samplight Z-Stack Home 1.2.2a for CC2530, 2538 SOC

Where to buy:

Setup the relay/Contactor, and button:

Prebuild hex:

Support gateway/hub/software:

Build it from scratch:

Step 1:

Step 2:

Step 3:

Step 4:

Configuration for Home Assistant

1 button

2 button

3 button

4 button

Dimmer version 1 gang (DC only):

Build it from scratch:

About

Releases

Packages

License

dzungpv/dnckatsw00x

Folders and files

Latest commit

History

Repository files navigation

Ligh Switch base on Samplight Z-Stack Home 1.2.2a for CC2530, 2538 SOC

Where to buy:

Setup the relay/Contactor, and button:

Prebuild hex:

Support gateway/hub/software:

Build it from scratch:

Step 1:

Step 2:

Step 3:

Step 4:

Configuration for Home Assistant

1 button

2 button

3 button

4 button

Dimmer version 1 gang (DC only):

Build it from scratch:

About

Resources

License

Stars

Watchers

Forks

Releases

Packages 0

Packages