WebUI inaccessible

[CFenner]

The Problem

I have 4 watermeters with AI on the edge, one of them I cannot setup as the web ui is inaccessible.

I tried another SD card and flashed the esp several times, behavior is always the same. Could this be an hardware issue?

Version

latest

Logfile

I (17646) LOGFILE: Set log level to ERROR
W (17686) FLOWCTRL: Rebooting to activate new RSSITHRESHOLD ...
I (17686) OTA: Reboot triggered by Software (5s)
W (17686) OTA: Reboot in 5sec
E (20696) wifi:NAN WiFi stop
ets Jun  8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:7664
load:0x40078000,len:15360
load:0x40080400,len:3744
entry 0x4008067c
I (27) boot: ESP-IDF 4.3.2 2nd stage bootloader
I (27) boot: compile time 20:02:47
I (27) boot: chip revision: 1
I (30) boot_comm: chip revision: 1, min. bootloader chip revision: 0
I (37) boot.esp32: SPI Speed      : 40MHz
I (41) boot.esp32: SPI Mode       : DIO
I (46) boot.esp32: SPI Flash Size : 4MB
I (51) boot: Enabling RNG early entropy source...
I (56) boot: Partition Table:
I (60) boot: ## Label            Usage          Type ST Offset   Length
I (67) boot:  0 nvs              WiFi data        01 02 00009000 00004000
I (74) boot:  1 otadata          OTA data         01 00 0000d000 00002000
I (82) boot:  2 phy_init         RF data          01 01 0000f000 00001000
I (89) boot:  3 ota_0            OTA app          00 10 00010000 001db000
I (97) boot:  4 ota_1            OTA app          00 11 001f0000 001db000
I (104) boot: End of partition table
I (109) boot_comm: chip revision: 1, min. application chip revision: 0
I (116) esp_image: segment 0: paddr=00010020 vaddr=3f400020 size=40014h (262164) map
I (225) esp_image: segment 1: paddr=0005003c vaddr=3ffb0000 size=040e8h ( 16616) load
I (232) esp_image: segment 2: paddr=0005412c vaddr=40080000 size=0beech ( 48876) load
I (253) esp_image: segment 3: paddr=00060020 vaddr=400d0020 size=1100f4h (1114356) map
I (680) esp_image: segment 4: paddr=0017011c vaddr=4008beec size=0e354h ( 58196) load
I (718) boot: Loaded app from partition at offset 0x10000
I (718) boot: Disabling RNG early entropy source...
I (730) cpu_start: Multicore app
I (730) quad_psram: This chip is ESP32-D0WD
I (730) esp_psram: Found 8MB PSRAM device
I (730) esp_psram: Speed: 40MHz
I (734) esp_psram: PSRAM initialized, cache is in low/high (2-core) mode.
W (741) esp_psram: Virtual address not enough for PSRAM, map as much as we can. 4MB is mapped
I (749) cpu_start: Pro cpu up.
I (752) cpu_start: Starting app cpu, entry point is 0x40082e0c
I (744) cpu_start: App cpu up.
I (1633) esp_psram: SPI SRAM memory test OK
I (1642) cpu_start: Pro cpu start user code
I (1642) cpu_start: cpu freq: 160000000 Hz
I (1642) cpu_start: Application information:
I (1643) cpu_start: Project name:     AI-on-the-edge
I (1647) cpu_start: App version:      v15.7.0
I (1651) cpu_start: Compile time:     Feb 17 2024 00:03:24
I (1657) cpu_start: ELF file SHA256:  71b36fda6e4066fa...
I (1662) cpu_start: ESP-IDF:          5.1.2
I (1666) cpu_start: Min chip rev:     v0.0
I (1670) cpu_start: Max chip rev:     v3.99 
I (1674) cpu_start: Chip rev:         v1.0
I (1678) heap_init: Initializing. RAM available for dynamic allocation:
I (1684) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM
I (1689) heap_init: At 3FFBC688 len 00023978 (142 KiB): DRAM
I (1694) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM
I (1700) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (1705) heap_init: At 4009A240 len 00005DC0 (23 KiB): IRAM
I (1711) esp_psram: Adding pool of 4082K of PSRAM memory to heap allocator
I (1719) spi_flash: detected chip: generic
I (1721) spi_flash: flash io: dio
I (1736) app_start: Starting scheduler on CPU0
I (1736) app_start: Starting scheduler on CPU1
I (1736) main_task: Started on CPU0
I (1746) esp_psram: Reserving pool of 40K of internal memory for DMA/internal allocations
I (1746) main_task: Calling app_main()
I (1746) MAIN: 



================ Start app_main =================
I (1866) MAIN: =================================================
I (1876) MAIN: ==================== Start ======================
I (1886) MAIN: =================================================
I (1886) MAIN: PSRAM size: 8388608 byte (8MB / 64MBit)
I (1896) MAIN: Total heap: 4380199 byte
I (1906) gpio: GPIO[32]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 
I (3906) gpio: GPIO[25]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:2 
I (3906) cam_hal: cam init ok
I (3906) sccb: pin_sda 26 pin_scl 27
I (3906) sccb: sccb_i2c_port=1
I (3906) gpio: GPIO[32]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 
I (3946) camera: Detected camera at address=0x30
I (3946) camera: Detected OV2640 camera
I (3946) camera: Camera PID=0x26 VER=0x42 MIDL=0x7f MIDH=0xa2
I (4026) cam_hal: buffer_size: 32768, half_buffer_size: 4096, node_buffer_size: 2048, node_cnt: 16, total_cnt: 15
I (4026) cam_hal: Allocating 61440 Byte frame buffer in PSRAM
I (4036) cam_hal: cam config ok
I (4036) ov2640: Set PLL: clk_2x: 0, clk_div: 0, pclk_auto: 0, pclk_div: 8
I (6116) MAIN: Camera info: PID: 0x26, VER: 0x42, MIDL: 0x7f, MIDH: 0xa2
I (6116) SDCARD: Basic R/W check started...
I (6146) SDCARD: Basic R/W check successful
I (6196) SNTP: TimeServer not defined, using default: pool.ntp.org
I (6206) SNTP: Configuring NTP Client...
I (6216) SNTP: Time zone set to CET-1CEST,M3.5.0,M10.5.0/3
I (6216) SNTP: time zone: +0200 Delta to UTC: 7200 seconds
I (6226) SNTP: Time is already set: 2024-06-08 23:10:14
I (6246) MAIN: CPU frequency: 160 MHz
I (6256) OTA: Start CheckOTAUpdateCheck...
I (6276) OTA: SHA-256 for the partition table: : 9d4a2809ae90fb20709a8ca3dd3ac3462e1e73286bcd31b689060c91de06fa3a
I (6296) OTA: SHA-256 for bootloader: : 4a9573dafac5d5c79c43e5a356568332da3a99dd2e220da6ceeadc96d32708a2
I (6676) OTA: SHA-256 for current firmware: : 9a05b58889422bcde87ba674b3146abea61153f01a9043d02ab6712d64cd4a6f
I (6716) SDCARD: Folder/file presence check started...
I (6756) SDCARD: Folder/file presence check successful
I (6776) MAIN: Tag: 'v15.7.0', Release: v15.7.0 (Commit: 0d0b018+), Date/Time: 2024-02-17 00:15, Web UI: Release: v15.7.0 (Commit: 0d0b018+)
I (6816) MAIN: Reset reason: Via esp_restart
I (6826) WLANINI: SSID: ...
I (6836) WLANINI: Password: XXXXXXXX
I (6846) WLANINI: Hostname: ESP32-Wasserzaehler-OG
I (6856) WLANINI: DNS: 192.168.5.50
I (6856) WLANINI: RSSIThreshold: -75
I (6866) MAIN: WLAN config loaded, init WIFI...
I (6876) WIFI: Automatic interface config --> Use DHCP service
I (6896) wifi:wifi driver task: 3ffcff14, prio:23, stack:6144, core=0
I (6906) wifi:wifi firmware version: 91b9630
I (6906) wifi:wifi certification version: v7.0
I (6906) wifi:config NVS flash: enabled
I (6916) wifi:config nano formating: enabled
I (6916) wifi:Init data frame dynamic rx buffer num: 16
I (6916) wifi:Init static rx mgmt buffer num: 5
I (6926) wifi:Init management short buffer num: 32
I (6926) wifi:Init static tx buffer num: 16
I (6936) wifi:Init tx cache buffer num: 16
I (6936) wifi:Init static rx buffer size: 1600
I (6936) wifi:Init static rx buffer num: 16
I (6946) wifi:Init dynamic rx buffer num: 16
I (6946) wifi_init: rx ba win: 16
I (6956) wifi_init: tcpip mbox: 32
I (6956) wifi_init: udp mbox: 6
I (6956) wifi_init: tcp mbox: 6
I (6956) wifi_init: tcp tx win: 5744
I (6966) wifi_init: tcp rx win: 5744
I (6966) wifi_init: tcp mss: 1440
I (6966) wifi_init: WiFi/LWIP prefer SPIRAM
I (6976) wifi_init: WiFi IRAM OP enabled
I (6976) wifi_init: WiFi RX IRAM OP enabled
I (6986) phy_init: phy_version 4780,16b31a7,Sep 22 2023,20:42:16
I (7066) wifi:mode : sta (40:22:d8:04:e4:14)
I (7076) wifi:enable tsf
I (7076) WIFI: Set hostname to: ESP32-Wasserzaehler-OG
I (7086) WIFI: Init successful
I (9486) wifi:new:<6,0>, old:<1,0>, ap:<255,255>, sta:<6,0>, prof:1
I (9496) wifi:state: init -> auth (b0)
I (9506) wifi:state: auth -> assoc (0)
I (9526) wifi:state: assoc -> run (10)
I (9726) wifi:connected with ..., aid = 2, channel 6, BW20, bssid = ea:38:83:25:33:92
I (9726) wifi:security: WPA2-PSK, phy: bgn, rssi: -44
I (9736) wifi:pm start, type: 1

I (9736) WIFI: Connected to: ..., RSSI: -44
I (9806) wifi:<ba-add>idx:0 (ifx:0, ea:38:83:25:33:92), tid:6, ssn:3, winSize:64
I (9826) wifi:AP's beacon interval = 102400 us, DTIM period = 1
I (10736) esp_netif_handlers: sta ip: ..., mask: ..., gw: ...
I (10736) WIFI: Assigned IP: ...
I (13736) wifi:<ba-add>idx:1 (ifx:0, ea:38:83:25:33:92), tid:0, ssn:0, winSize:64
I (13766) SNTP: Time is synced with NTP Server pool.ntp.org: 2024-06-08 23:10:21
I (15096) MAIN: Device info: CPU cores: 2, Chip revision: 100
I (15096) MAIN: SD card info: Name: SH32G, Capacity: 30436MB, Free: 30412MB
I (17106) MAIN SERVER: Starting server on port: '80'
I (17106) MAIN SERVER: Registering URI handlers
I (17106) MAINCTRL: server_main_flow_task - Registering URI handlers
I (17106) OTA: Registering URI handlers
I (17106) GPIO: start GpioHandler
I (17116) GPIO: register GPIO Uri
I (17116) GPIO: server_GPIO - Registering URI handlers
I (17116) MAIN: Initialization completed successfully
I (17136) main_task: Returned from app_main()
I (17176) ov2640: Set PLL: clk_2x: 0, clk_div: 0, pclk_auto: 0, pclk_div: 8
I (19276) LOGFILE: Set log level to ERROR
I (19286) GPIO: read GPIO config and init GPIO
I (19306) GPIO: GPIO init completed, handler is disabled
I (19306) MAINCTRL: We are in Setup Mode -> Not starting Auto Flow!
I (28886) MAINCTRL: Autostart is not enabled -> Not starting Flow
W (47766) httpd_txrx: httpd_sock_err: error in send : 104
E (47766) SERVER HELP: File sending failed!
W (47766) httpd_txrx: httpd_sock_err: error in send : 104
W (47766) httpd_txrx: httpd_resp_send_err: 500 Internal Server Error - Failed to send file
W (47776) httpd_txrx: httpd_resp_send_err: error calling setsockopt : 22
W (47786) httpd_txrx: httpd_sock_err: error in send : 128
W (47786) httpd_txrx: httpd_sock_err: error in send : 128
W (47796) httpd_uri: httpd_uri: uri handler execution failed
W (48066) httpd_txrx: httpd_sock_err: error in send : 104
E (48066) SERVER HELP: File sending failed!
W (48066) httpd_txrx: httpd_sock_err: error in send : 104
W (48076) httpd_txrx: httpd_resp_send_err: 500 Internal Server Error - Failed to send file
W (48076) httpd_txrx: httpd_resp_send_err: error calling setsockopt : 22
W (48086) httpd_txrx: httpd_sock_err: error in send : 128
W (48096) httpd_txrx: httpd_sock_err: error in send : 128
W (48096) httpd_uri: httpd_uri: uri handler execution failed
W (690516) httpd_txrx: httpd_sock_err: error in recv : 104
Terminal disconnected: NetworkError: The device has been lost.

Expected Behavior

No response

Screenshots

No response

Additional Context

No response

[caco3]

httpd_txrx: httpd_sock_err: error in send : 104

Those warnings can be ignored, they also occur on good devices / normal operation.

W (47766) httpd_txrx: httpd_resp_send_err: 500 Internal Server Error - Failed to send file

Could you try an SD card of one of the good devices?

Else its hard to tell. It could be a HW issue, but there is no real indication for this.