Detailed support for Tornado/Sanyo 88-bit A/C protocol

src/IRac.cpp

@@ -259,6 +259,9 @@ bool IRac::isProtocolSupported(const decode_type_t protocol) {
 #if SEND_SANYO_AC
     case decode_type_t::SANYO_AC:
 #endif
+#if SEND_SANYO_AC88
+    case decode_type_t::SANYO_AC88:
+#endif
 #if SEND_SHARP_AC
     case decode_type_t::SHARP_AC:
 #endif
@@ -1766,7 +1769,7 @@ void IRac::samsung(IRSamsungAc *ac,
 #endif  // SEND_SAMSUNG_AC
 
 #if SEND_SANYO_AC
-/// Send a Toshiba A/C message with the supplied settings.
+/// Send a Sanyo A/C message with the supplied settings.
 /// @param[in, out] ac A Ptr to an IRSanyoAc object to use.
 /// @param[in] on The power setting.
 /// @param[in] mode The operation mode setting.
@@ -1804,6 +1807,44 @@ void IRac::sanyo(IRSanyoAc *ac,
 }
 #endif  // SEND_SANYO_AC
 
+#if SEND_SANYO_AC88
+/// Send a Sanyo 88-bit A/C message with the supplied settings.
+/// @param[in, out] ac A Ptr to an IRSanyoAc88 object to use.
+/// @param[in] on The power setting.
+/// @param[in] mode The operation mode setting.
+/// @param[in] degrees The temperature setting in degrees.
+/// @param[in] fan The speed setting for the fan.
+/// @param[in] swingv The vertical swing setting.
+/// @param[in] turbo Run the device in turbo/powerful mode.
+/// @param[in] filter Turn on the (ion/pollen/etc) filter mode.
+/// @param[in] sleep Nr. of minutes for sleep mode. -1 is Off, >= 0 is on.
+/// @param[in] clock The time in Nr. of mins since midnight. < 0 is ignore.
+void IRac::sanyo88(IRSanyoAc88 *ac,
+                   const bool on, const stdAc::opmode_t mode,
+                   const float degrees, const stdAc::fanspeed_t fan,
+                   const stdAc::swingv_t swingv, const bool turbo,
+                   const bool filter, const int16_t sleep,
+                   const int16_t clock) {
+  ac->begin();
+  ac->setPower(on);
+  ac->setMode(ac->convertMode(mode));
+  ac->setTemp(degrees);
+  ac->setFan(ac->convertFan(fan));
+  ac->setSwingV(swingv != stdAc::swingv_t::kOff);
+  // No Horizontal swing setting available.
+  // No Quiet setting available.
+  ac->setTurbo(turbo);
+  // No Econo setting available.
+  // No Light setting available.
+  ac->setFilter(filter);
+  // No Clean setting available.
+  // No Beep setting available.
+  ac->setSleep(sleep >= 0);  // Sleep is either on/off, so convert to boolean.
+  if (clock >= 0) ac->setClock(clock);
+  ac->send();
+}
+#endif  // SEND_SANYO_AC88
+
 #if SEND_SHARP_AC
 /// Send a Sharp A/C message with the supplied settings.
 /// @note Multiple IR messages may be generated & sent.
@@ -2798,6 +2839,15 @@ bool IRac::sendAc(const stdAc::state_t desired, const stdAc::state_t *prev) {
       break;
     }
 #endif  // SEND_SANYO_AC
+#if SEND_SANYO_AC88
+    case SANYO_AC88:
+    {
+      IRSanyoAc88 ac(_pin, _inverted, _modulation);
+      sanyo88(&ac, send.power, send.mode, degC, send.fanspeed, send.swingv,
+              send.turbo, send.filter, send.sleep, send.clock);
+      break;
+    }
+#endif  // SEND_SANYO_AC88
 #if SEND_SHARP_AC
     case SHARP_AC:
     {
@@ -2912,7 +2962,7 @@ bool IRac::sendAc(const stdAc::state_t desired, const stdAc::state_t *prev) {
       return false;  // Fail, didn't match anything.
   }
   return true;  // Success.
-}
+}  // NOLINT(readability/fn_size)
 
 /// Update the previous state to the current one.
 void IRac::markAsSent(void) {
@@ -3529,6 +3579,13 @@ namespace IRAcUtils {
         return ac.toString();
       }
 #endif  // DECODE_SANYO_AC
+#if DECODE_SANYO_AC88
+      case decode_type_t::SANYO_AC88: {
+        IRSanyoAc88 ac(kGpioUnused);
+        ac.setRaw(result->state);
+        return ac.toString();
+      }
+#endif  // DECODE_SANYO_AC88
 #if DECODE_SHARP_AC
       case decode_type_t::SHARP_AC: {
         IRSharpAc ac(kGpioUnused);
@@ -4006,6 +4063,14 @@ namespace IRAcUtils {
         break;
       }
 #endif  // DECODE_SANYO_AC
+#if DECODE_SANYO_AC88
+      case decode_type_t::SANYO_AC88: {
+        IRSanyoAc88 ac(kGpioUnused);
+        ac.setRaw(decode->state);
+        *result = ac.toCommon();
+        break;
+      }
+#endif  // DECODE_SANYO_AC88
 #if DECODE_SHARP_AC
       case decode_type_t::SHARP_AC: {
         IRSharpAc ac(kGpioUnused);

src/IRac.h

@@ -393,6 +393,14 @@ void electra(IRElectraAc *ac,
              const stdAc::fanspeed_t fan, const stdAc::swingv_t swingv,
              const bool beep, const int16_t sleep = -1);
 #endif  // SEND_SANYO_AC
+#if SEND_SANYO_AC88
+  void sanyo88(IRSanyoAc88 *ac,
+                   const bool on, const stdAc::opmode_t mode,
+                   const float degrees, const stdAc::fanspeed_t fan,
+                   const stdAc::swingv_t swingv, const bool turbo,
+                   const bool filter,
+                   const int16_t sleep = -1, const int16_t clock = -1);
+#endif  // SEND_SANYO_AC88
 #if SEND_SHARP_AC
   void sharp(IRSharpAc *ac, const sharp_ac_remote_model_t model,
              const bool on, const bool prev_power, const stdAc::opmode_t mode,

src/IRrecv.cpp

@@ -1028,6 +1028,10 @@ bool IRrecv::decode(decode_results *results, irparams_t *save,
     DPRINTLN("Attempting Kelon decode");
     if (decodeKelon(results, offset)) return true;
 #endif  // DECODE_KELON
+#if DECODE_SANYO_AC88
+    DPRINTLN("Attempting SanyoAc88 decode");
+    if (decodeSanyoAc88(results, offset)) return true;
+#endif  // DECODE_SANYO_AC88
   // Typically new protocols are added above this line.
   }
 #if DECODE_HASH

src/IRrecv.h

@@ -308,6 +308,12 @@ class IRrecv {
                      const uint16_t nbits = kSanyoAcBits,
                      const bool strict = true);
 #endif  // DECODE_SANYO_AC
+#if DECODE_SANYO_AC88
+  bool decodeSanyoAc88(decode_results *results,
+                       uint16_t offset = kStartOffset,
+                       const uint16_t nbits = kSanyoAc88Bits,
+                       const bool strict = true);
+#endif  // DECODE_SANYO_AC88
 #if DECODE_MITSUBISHI
   bool decodeMitsubishi(decode_results *results, uint16_t offset = kStartOffset,
                         const uint16_t nbits = kMitsubishiBits,

src/IRremoteESP8266.h

@@ -209,6 +209,13 @@
 #define SEND_SANYO_AC          _IR_ENABLE_DEFAULT_
 #endif  // SEND_SANYO_AC
 
+#ifndef DECODE_SANYO_AC88
+#define DECODE_SANYO_AC88      _IR_ENABLE_DEFAULT_
+#endif  // DECODE_SANYO_AC88
+#ifndef SEND_SANYO_AC88
+#define SEND_SANYO_AC88        _IR_ENABLE_DEFAULT_
+#endif  // SEND_SANYO_AC88
+
 #ifndef DECODE_MITSUBISHI
 #define DECODE_MITSUBISHI      _IR_ENABLE_DEFAULT_
 #endif  // DECODE_MITSUBISHI
@@ -790,6 +797,7 @@
      DECODE_HITACHI_AC344 || DECODE_CORONA_AC || DECODE_SANYO_AC || \
      DECODE_VOLTAS || DECODE_MIRAGE || DECODE_HAIER_AC176 || \
      DECODE_TEKNOPOINT || DECODE_KELON || DECODE_TROTEC_3550 || \
+     DECODE_SANYO_AC88 || \
      false)
   // Add any DECODE to the above if it uses result->state (see kStateSizeMax)
   // you might also want to add the protocol to hasACState function
@@ -934,8 +942,9 @@ enum decode_type_t {
   TEKNOPOINT,
   KELON,
   TROTEC_3550,
+  SANYO_AC88,  // 105
   // Add new entries before this one, and update it to point to the last entry.
-  kLastDecodeType = TROTEC_3550,
+  kLastDecodeType = SANYO_AC88,
 };
 
 // Message lengths & required repeat values
@@ -1121,6 +1130,9 @@ const uint16_t kSamsungAcExtendedBits = kSamsungAcExtendedStateLength * 8;
 const uint16_t kSamsungAcDefaultRepeat = kNoRepeat;
 const uint16_t kSanyoAcStateLength = 9;
 const uint16_t kSanyoAcBits = kSanyoAcStateLength * 8;
+const uint16_t kSanyoAc88StateLength = 11;
+const uint16_t kSanyoAc88Bits = kSanyoAc88StateLength * 8;
+const uint16_t kSanyoAc88MinRepeat = 2;
 const uint16_t kSanyoSA8650BBits = 12;
 const uint16_t kSanyoLC7461AddressBits = 13;
 const uint16_t kSanyoLC7461CommandBits = 8;

src/IRsend.cpp

@@ -580,6 +580,8 @@ uint16_t IRsend::minRepeats(const decode_type_t protocol) {
       return kDishMinRepeat;
     case EPSON:
       return kEpsonMinRepeat;
+    case SANYO_AC88:
+      return kSanyoAc88MinRepeat;
     case SONY:
       return kSonyMinRepeat;
     case SONY_38K:
@@ -739,6 +741,8 @@ uint16_t IRsend::defaultBits(const decode_type_t protocol) {
       return kSamsungAcBits;
     case SANYO_AC:
       return kSanyoAcBits;
+    case SANYO_AC88:
+      return kSanyoAc88Bits;
     case SHARP_AC:
       return kSharpAcBits;
     case TCL112AC:
@@ -1247,6 +1251,11 @@ bool IRsend::send(const decode_type_t type, const uint8_t *state,
       sendSanyoAc(state, nbytes);
       break;
 #endif  // SEND_SANYO_AC
+#if SEND_SANYO_AC88
+    case SANYO_AC88:
+      sendSanyoAc88(state, nbytes);
+      break;
+#endif  // SEND_SANYO_AC88
 #if SEND_SHARP_AC
     case SHARP_AC:
       sendSharpAc(state, nbytes);

src/IRsend.h

@@ -319,6 +319,11 @@ class IRsend {
                    const uint16_t nbytes = kSanyoAcStateLength,
                    const uint16_t repeat = kNoRepeat);
 #endif  // SEND_SANYO_AC
+#if SEND_SANYO_AC88
+  void sendSanyoAc88(const uint8_t *data,
+                     const uint16_t nbytes = kSanyoAc88StateLength,
+                     const uint16_t repeat = kSanyoAc88MinRepeat);
+#endif  // SEND_SANYO_AC88
 #if SEND_DISH
   // sendDISH() should typically be called with repeat=3 as DISH devices
   // expect the code to be sent at least 4 times. (code + 3 repeats = 4 codes)

src/IRtext.cpp

@@ -290,5 +290,6 @@ const PROGMEM char *kAllProtocolNamesStr =
     D_STR_TEKNOPOINT "\x0"
     D_STR_KELON "\x0"
     D_STR_TROTEC_3550 "\x0"
+    D_STR_SANYO_AC88 "\x0"
     ///< New protocol strings should be added just above this line.
     "\x0";  ///< This string requires double null termination.

src/IRutils.cpp

@@ -177,6 +177,7 @@ bool hasACState(const decode_type_t protocol) {
     case PANASONIC_AC:
     case SAMSUNG_AC:
     case SANYO_AC:
+    case SANYO_AC88:
     case SHARP_AC:
     case TCL112AC:
     case TEKNOPOINT: