E-Ink Screensaver

src/graphics/EInkDisplay2.cpp

@@ -184,7 +184,6 @@ bool EInkDisplay::connect()
         // Init GxEPD2
         adafruitDisplay->init();
         adafruitDisplay->setRotation(3);
-        adafruitDisplay->clearScreen(); // Clearing now, so the boot logo will draw nice and smoothe (fast refresh)
     }
 #elif defined(PCA10059)
     {

src/graphics/EInkDynamicDisplay.cpp

@@ -5,7 +5,7 @@
 
 // Constructor
 EInkDynamicDisplay::EInkDynamicDisplay(uint8_t address, int sda, int scl, OLEDDISPLAY_GEOMETRY geometry, HW_I2C i2cBus)
-    : EInkDisplay(address, sda, scl, geometry, i2cBus)
+    : EInkDisplay(address, sda, scl, geometry, i2cBus), NotifiedWorkerThread("EInkDynamicDisplay")
 {
     // If tracking ghost pixels, grab memory
 #ifdef EINK_LIMIT_GHOSTING_PX
@@ -112,12 +112,15 @@ void EInkDynamicDisplay::endOrDetach()
     // If the GxEPD2 version reports that it has the async modifications
 #ifdef HAS_EINK_ASYNCFULL
     if (previousRefresh == FULL) {
-        asyncRefreshRunning = true; // Set the flag - picked up at start of determineMode(), next loop.
+        asyncRefreshRunning = true; // Set the flag - checked in determineMode(); cleared by onNotify()
 
         if (previousFrameFlags & BLOCKING)
             awaitRefresh();
-        else
-            LOG_DEBUG("Async full-refresh begins\n");
+        else {
+            // Async begins
+            LOG_DEBUG("Async full-refresh begins (dropping frames)\n");
+            notifyLater(intervalPollAsyncRefresh, DUE_POLL_ASYNCREFRESH, true); // Hand-off to NotifiedWorkerThread
+        }
     }
 
     // Fast Refresh
@@ -141,7 +144,7 @@ bool EInkDynamicDisplay::determineMode()
     checkInitialized();
     checkForPromotion();
 #if defined(HAS_EINK_ASYNCFULL)
-    checkAsyncFullRefresh();
+    checkBusyAsyncRefresh();
 #endif
     checkRateLimiting();
 
@@ -252,6 +255,7 @@ void EInkDynamicDisplay::checkRateLimiting()
         if (now - previousRunMs < EINK_LIMIT_RATE_RESPONSIVE_SEC * 1000) {
             refresh = SKIPPED;
             reason = EXCEEDED_RATELIMIT_FAST;
+            LOG_DEBUG("refresh=SKIPPED, reason=EXCEEDED_RATELIMIT_FAST, frameFlags=0x%x\n", frameFlags);
             return;
         }
     }
@@ -447,9 +451,44 @@ void EInkDynamicDisplay::resetGhostPixelTracking()
 }
 #endif // EINK_LIMIT_GHOSTING_PX
 
+// Handle any asyc tasks
+void EInkDynamicDisplay::onNotify(uint32_t notification)
+{
+    // Which task
+    switch (notification) {
+    case DUE_POLL_ASYNCREFRESH:
+        pollAsyncRefresh();
+        break;
+    }
+}
+
 #ifdef HAS_EINK_ASYNCFULL
-// Check the status of an "async full-refresh", and run the finish-up code if the hardware is ready
-void EInkDynamicDisplay::checkAsyncFullRefresh()
+// Run the post-update code if the hardware is ready
+void EInkDynamicDisplay::pollAsyncRefresh()
+{
+    // We shouldn't be here..
+    if (!asyncRefreshRunning)
+        return;
+
+    // Still running, check back later
+    if (adafruitDisplay->epd2.isBusy()) {
+        // Schedule next call of pollAsyncRefresh()
+        NotifiedWorkerThread::notifyLater(intervalPollAsyncRefresh, DUE_POLL_ASYNCREFRESH, true);
+        return;
+    }
+
+    // If asyncRefreshRunning flag is still set, but display's BUSY pin reports the refresh is done
+    adafruitDisplay->endAsyncFull(); // Run the end of nextPage() code
+    EInkDisplay::endUpdate();        // Run base-class code to finish off update (NOT our derived class override)
+    asyncRefreshRunning = false;     // Unset the flag
+    LOG_DEBUG("Async full-refresh complete\n");
+
+    // Note: this code only works because of a modification to meshtastic/GxEPD2.
+    // It is only equipped to intercept calls to nextPage()
+}
+
+// Check the status of "async full-refresh"; skip if running
+void EInkDynamicDisplay::checkBusyAsyncRefresh()
 {
     // No refresh taking place, continue with determineMode()
     if (!asyncRefreshRunning)
@@ -472,15 +511,6 @@ void EInkDynamicDisplay::checkAsyncFullRefresh()
 
         return;
     }
-
-    // If we asyncRefreshRunning flag is still set, but display's BUSY pin reports the refresh is done
-    adafruitDisplay->endAsyncFull(); // Run the end of nextPage() code
-    EInkDisplay::endUpdate();        // Run base-class code to finish off update (NOT our derived class override)
-    asyncRefreshRunning = false;     // Unset the flag
-    LOG_DEBUG("Async full-refresh complete\n");
-
-    // Note: this code only works because of a modification to meshtastic/GxEPD2.
-    // It is only equipped to intercept calls to nextPage()
 }
 
 // Hold control while an async refresh runs

src/graphics/EInkDynamicDisplay.h

@@ -6,6 +6,7 @@
 
 #include "EInkDisplay2.h"
 #include "GxEPD2_BW.h"
+#include "concurrency/NotifiedWorkerThread.h"
 
 /*
     Derives from the EInkDisplay adapter class.
@@ -14,7 +15,7 @@
     (Full, Fast, Skip)
 */
 
-class EInkDynamicDisplay : public EInkDisplay
+class EInkDynamicDisplay : public EInkDisplay, protected concurrency::NotifiedWorkerThread
 {
   public:
     // Constructor
@@ -61,13 +62,20 @@ class EInkDynamicDisplay : public EInkDisplay
         REDRAW_WITH_FULL,
     };
 
-    void configForFastRefresh();  // GxEPD2 code to set fast-refresh
-    void configForFullRefresh();  // GxEPD2 code to set full-refresh
-    bool determineMode();         // Assess situation, pick a refresh type
-    void applyRefreshMode();      // Run any relevant GxEPD2 code, so next update will use correct refresh type
-    void adjustRefreshCounters(); // Update fastRefreshCount
-    bool update();                // Trigger the display update - determine mode, then call base class
-    void endOrDetach();           // Run the post-update code, or delegate it off to checkAsyncFullRefresh()
+    enum notificationTypes : uint8_t { // What was onNotify() called for
+        NONE = 0,                      // This behavior (NONE=0) is fixed by NotifiedWorkerThread class
+        DUE_POLL_ASYNCREFRESH = 1,
+    };
+    const uint32_t intervalPollAsyncRefresh = 100;
+
+    void onNotify(uint32_t notification) override; // Handle any async tasks - overrides NotifiedWorkerThread
+    void configForFastRefresh();                   // GxEPD2 code to set fast-refresh
+    void configForFullRefresh();                   // GxEPD2 code to set full-refresh
+    bool determineMode();                          // Assess situation, pick a refresh type
+    void applyRefreshMode();                       // Run any relevant GxEPD2 code, so next update will use correct refresh type
+    void adjustRefreshCounters();                  // Update fastRefreshCount
+    bool update();                                 // Trigger the display update - determine mode, then call base class
+    void endOrDetach();                            // Run the post-update code, or delegate it off to checkBusyAsyncRefresh()
 
     // Checks as part of determineMode()
     void checkInitialized();              // Is this the very first frame?
@@ -111,10 +119,13 @@ class EInkDynamicDisplay : public EInkDisplay
 
     // Conditional - async full refresh - only with modified meshtastic/GxEPD2
 #if defined(HAS_EINK_ASYNCFULL)
-    void checkAsyncFullRefresh(); // Check the status of "async full-refresh"; run the post-update code if the hardware is ready
-    void awaitRefresh();          // Hold control while an async refresh runs
-    void endUpdate() override {}  // Disable base-class behavior of running post-update immediately after forceDisplay()
-    bool asyncRefreshRunning = false; // Flag, checked by checkAsyncFullRefresh()
+    void pollAsyncRefresh();          // Run the post-update code if the hardware is ready
+    void checkBusyAsyncRefresh();     // Check if display is busy running an async full-refresh (rejecting new frames)
+    void awaitRefresh();              // Hold control while an async refresh runs
+    void endUpdate() override {}      // Disable base-class behavior of running post-update immediately after forceDisplay()
+    bool asyncRefreshRunning = false; // Flag, checked by checkBusyAsyncRefresh()
+#else
+    void pollAsyncRefresh() {} // Dummy method. In theory, not reachable
 #endif
 };
 

src/graphics/Screen.cpp

@@ -262,14 +262,65 @@ static void drawWelcomeScreen(OLEDDisplay *display, OLEDDisplayUiState *state, i
 
 #ifdef USE_EINK
 /// Used on eink displays while in deep sleep
-static void drawSleepScreen(OLEDDisplay *display, OLEDDisplayUiState *state, int16_t x, int16_t y)
+static void drawDeepSleepScreen(OLEDDisplay *display, OLEDDisplayUiState *state, int16_t x, int16_t y)
 {
     // Next frame should use full-refresh, and block while running, else device will sleep before async callback
     EINK_ADD_FRAMEFLAG(display, COSMETIC);
     EINK_ADD_FRAMEFLAG(display, BLOCKING);
 
+    LOG_DEBUG("Drawing deep sleep screen\n");
     drawIconScreen("Sleeping...", display, state, x, y);
 }
+
+/// Used on eink displays when screen updates are paused
+static void drawScreensaverOverlay(OLEDDisplay *display, OLEDDisplayUiState *state)
+{
+    LOG_DEBUG("Drawing screensaver overlay\n");
+
+    EINK_ADD_FRAMEFLAG(display, COSMETIC); // Take the opportunity for a full-refresh
+
+    // Config
+    display->setFont(FONT_SMALL);
+    display->setTextAlignment(TEXT_ALIGN_LEFT);
+    const char *pauseText = "Screen Paused";
+    const char *idText = owner.short_name;
+    constexpr uint16_t padding = 5;
+    constexpr uint8_t dividerGap = 1;
+    constexpr uint8_t imprecision = 5; // How far the box origins can drift from center. Combat burn-in.
+
+    // Dimensions
+    const uint16_t idTextWidth = display->getStringWidth(idText, strlen(idText));
+    const uint16_t pauseTextWidth = display->getStringWidth(pauseText, strlen(pauseText));
+    const uint16_t boxWidth = padding + idTextWidth + padding + padding + pauseTextWidth + padding;
+    const uint16_t boxHeight = padding + FONT_HEIGHT_SMALL + padding;
+
+    // Position
+    const int16_t boxLeft = (display->width() / 2) - (boxWidth / 2) + random(-imprecision, imprecision + 1);
+    // const int16_t boxRight = boxLeft + boxWidth - 1;
+    const int16_t boxTop = (display->height() / 2) - (boxHeight / 2 + random(-imprecision, imprecision + 1));
+    const int16_t boxBottom = boxTop + boxHeight - 1;
+    const int16_t idTextLeft = boxLeft + padding;
+    const int16_t idTextTop = boxTop + padding;
+    const int16_t pauseTextLeft = boxLeft + padding + idTextWidth + padding + padding;
+    const int16_t pauseTextTop = boxTop + padding;
+    const int16_t dividerX = boxLeft + padding + idTextWidth + padding;
+    const int16_t dividerTop = boxTop + 1 + dividerGap;
+    const int16_t dividerBottom = boxBottom - 1 - dividerGap;
+
+    // Draw: box
+    display->setColor(EINK_WHITE);
+    display->fillRect(boxLeft - 1, boxTop - 1, boxWidth + 2, boxHeight + 2); // Clear a slightly oversized area for the box
+    display->setColor(EINK_BLACK);
+    display->drawRect(boxLeft, boxTop, boxWidth, boxHeight);
+
+    // Draw: Text
+    display->drawString(idTextLeft, idTextTop, idText);
+    display->drawString(pauseTextLeft, pauseTextTop, pauseText);
+    display->drawString(pauseTextLeft + 1, pauseTextTop, pauseText); // Faux bold
+
+    // Draw: divider
+    display->drawLine(dividerX, dividerTop, dividerX, dividerBottom);
+}
 #endif
 
 static void drawModuleFrame(OLEDDisplay *display, OLEDDisplayUiState *state, int16_t x, int16_t y)
@@ -948,18 +999,17 @@ Screen::~Screen()
 void Screen::doDeepSleep()
 {
 #ifdef USE_EINK
-    static FrameCallback sleepFrames[] = {drawSleepScreen};
-    static const int sleepFrameCount = sizeof(sleepFrames) / sizeof(sleepFrames[0]);
-    ui->setFrames(sleepFrames, sleepFrameCount);
-    ui->update();
+    setOn(false, drawDeepSleepScreen);
 #ifdef PIN_EINK_EN
     digitalWrite(PIN_EINK_EN, LOW); // power off backlight
 #endif
-#endif
+#else
+    // Without E-Ink display:
     setOn(false);
+#endif
 }
 
-void Screen::handleSetOn(bool on)
+void Screen::handleSetOn(bool on, FrameCallback einkScreensaver)
 {
     if (!useDisplay)
         return;
@@ -978,6 +1028,10 @@ void Screen::handleSetOn(bool on)
             setInterval(0); // Draw ASAP
             runASAP = true;
         } else {
+#ifdef USE_EINK
+            // eInkScreensaver parameter is usually NULL (default argument), default frame used instead
+            setScreensaverFrames(einkScreensaver);
+#endif
             LOG_INFO("Turning off screen\n");
             dispdev->displayOff();
 #ifdef T_WATCH_S3
@@ -1028,6 +1082,7 @@ void Screen::setup()
         logo_timeout *= 2;
 
     // Add frames.
+    EINK_ADD_FRAMEFLAG(dispdev, DEMAND_FAST);
     static FrameCallback bootFrames[] = {drawBootScreen};
     static const int bootFrameCount = sizeof(bootFrames) / sizeof(bootFrames[0]);
     ui->setFrames(bootFrames, bootFrameCount);
@@ -1283,6 +1338,58 @@ void Screen::setWelcomeFrames()
     }
 }
 
+#ifdef USE_EINK
+/// Determine which screensaver frame to use, then set the FrameCallback
+void Screen::setScreensaverFrames(FrameCallback einkScreensaver)
+{
+    // Remember current frame, restore position at power-on
+    uint8_t frameNumber = ui->getUiState()->currentFrame;
+
+    // Retain specified frame / overlay callback beyond scope of this method
+    static FrameCallback screensaverFrame;
+    static OverlayCallback screensaverOverlay;
+
+    // If: one-off screensaver frame passed as argument. Handles doDeepSleep()
+    if (einkScreensaver != NULL) {
+        screensaverFrame = einkScreensaver;
+        ui->setFrames(&screensaverFrame, 1);
+    }
+
+    // Else, display the usual "overlay" screensaver
+    else {
+        screensaverOverlay = drawScreensaverOverlay;
+        ui->setOverlays(&screensaverOverlay, 1);
+    }
+
+    // Request new frame, ASAP
+    setFastFramerate();
+    uint64_t startUpdate;
+    do {
+        startUpdate = millis(); // Handle impossibly unlikely corner case of a millis() overflow..
+        delay(1);
+        ui->update();
+    } while (ui->getUiState()->lastUpdate < startUpdate);
+
+#ifndef USE_EINK_DYNAMICDISPLAY
+    // Retrofit to EInkDisplay class
+    delay(10);
+    screen->forceDisplay();
+#endif
+
+    // Prepare now for next frame, shown when display wakes
+    ui->setOverlays(NULL, 0);       // Clear overlay
+    setFrames();                    // Return to normal display updates
+    ui->switchToFrame(frameNumber); // Attempt to return to same frame after power-on
+
+    // Pick a refresh method, for when display wakes
+#ifdef EINK_HASQUIRK_GHOSTING
+    EINK_ADD_FRAMEFLAG(dispdev, COSMETIC); // Really ugly to see ghosting from "screen paused"
+#else
+    EINK_ADD_FRAMEFLAG(dispdev, RESPONSIVE); // Really nice to wake screen with a fast-refresh
+#endif
+}
+#endif
+
 // restore our regular frame list
 void Screen::setFrames()
 {
@@ -1383,14 +1490,16 @@ void Screen::handleShutdownScreen()
 {
     LOG_DEBUG("showing shutdown screen\n");
     showingNormalScreen = false;
-    EINK_ADD_FRAMEFLAG(dispdev, DEMAND_FAST); // E-Ink: Explicitly use fast-refresh for next frame
+    EINK_ADD_FRAMEFLAG(dispdev, DEMAND_FAST); // E-Ink: Use fast-refresh for next frame, no skip please
+    EINK_ADD_FRAMEFLAG(dispdev, BLOCKING);    // Edge case: if this frame is promoted to COSMETIC, wait for update
 
     auto frame = [](OLEDDisplay *display, OLEDDisplayUiState *state, int16_t x, int16_t y) -> void {
         drawFrameText(display, state, x, y, "Shutting down...");
     };
     static FrameCallback frames[] = {frame};
 
     setFrameImmediateDraw(frames);
+    forceDisplay();
 }
 
 void Screen::handleRebootScreen()