Lilygo T3S3 E-Paper support

src/graphics/EInkDisplay2.cpp

@@ -157,7 +157,7 @@ bool EInkDisplay::connect()
     }
 
 #elif defined(HELTEC_WIRELESS_PAPER_V1_0) || defined(HELTEC_WIRELESS_PAPER) || defined(HELTEC_VISION_MASTER_E213) ||             \
-    defined(HELTEC_VISION_MASTER_E290)
+    defined(HELTEC_VISION_MASTER_E290) || defined(TLORA_T3S3_EPAPER)
     {
         // Start HSPI
         hspi = new SPIClass(HSPI);

src/graphics/EInkDisplay2.h

@@ -68,7 +68,7 @@ class EInkDisplay : public OLEDDisplay
 
     // If display uses HSPI
 #if defined(HELTEC_WIRELESS_PAPER) || defined(HELTEC_WIRELESS_PAPER_V1_0) || defined(HELTEC_VISION_MASTER_E213) ||               \
-    defined(HELTEC_VISION_MASTER_E290)
+    defined(HELTEC_VISION_MASTER_E290) || defined(TLORA_T3S3_EPAPER)
     SPIClass *hspi = NULL;
 #endif
 

src/mesh/NodeDB.cpp

@@ -307,7 +307,7 @@ void NodeDB::installDefaultConfig()
 #else
     config.device.disable_triple_click = true;
 #endif
-#if !HAS_GPS || defined(T_DECK)
+#if !HAS_GPS || defined(T_DECK) || defined(TLORA_T3S3_EPAPER)
     config.position.gps_mode = meshtastic_Config_PositionConfig_GpsMode_NOT_PRESENT;
 #elif !defined(GPS_RX_PIN)
     if (config.position.rx_gpio == 0)

src/platform/esp32/architecture.h

@@ -122,6 +122,8 @@
 #define HW_VENDOR meshtastic_HardwareModel_HELTEC_WIRELESS_PAPER
 #elif defined(TLORA_T3S3_V1)
 #define HW_VENDOR meshtastic_HardwareModel_TLORA_T3_S3
+#elif defined(TLORA_T3S3_EPAPER)
+#define HW_VENDOR meshtastic_HardwareModel_TLORA_T3_S3
 #elif defined(CDEBYTE_EORA_S3)
 #define HW_VENDOR meshtastic_HardwareModel_CDEBYTE_EORA_S3
 #elif defined(BETAFPV_2400_TX)

variants/tlora_t3s3_epaper/pins_arduino.h

@@ -0,0 +1,26 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// The default Wire will be mapped to PMU and RTC
+static const uint8_t SDA = 18;
+static const uint8_t SCL = 12; // t3s3 e-Paper has no pin 17 as t3s3 v1, so use another free pin next to it
+
+// Default SPI will be mapped to Radio
+static const uint8_t SS = 7;
+static const uint8_t MOSI = 6;
+static const uint8_t MISO = 3;
+static const uint8_t SCK = 5;
+
+#define SPI_MOSI (11)
+#define SPI_SCK (14)
+#define SPI_MISO (2)
+#define SPI_CS (13)
+
+#define SDCARD_CS SPI_CS
+
+#endif /* Pins_Arduino_h */

variants/tlora_t3s3_epaper/platformio.ini

@@ -0,0 +1,23 @@
+[env:tlora-t3s3-epaper]
+extends = esp32s3_base
+board = tlora-t3s3-v1
+board_check = true
+upload_protocol = esptool
+
+build_flags = 
+  ${esp32_base.build_flags} -D TLORA_T3S3_EPAPER -I variants/tlora_t3s3_epaper
+  -DGPS_POWER_TOGGLE
+  -DEINK_DISPLAY_MODEL=GxEPD2_213_BN
+  -DEINK_WIDTH=250
+  -DEINK_HEIGHT=122
+  -DUSE_EINK_DYNAMICDISPLAY            ; Enable Dynamic EInk
+  -DEINK_LIMIT_FASTREFRESH=10          ; How many consecutive fast-refreshes are permitted
+  -DEINK_LIMIT_RATE_BACKGROUND_SEC=30  ; Minimum interval between BACKGROUND updates
+  -DEINK_LIMIT_RATE_RESPONSIVE_SEC=1   ; Minimum interval between RESPONSIVE updates
+  -DEINK_HASQUIRK_VICIOUSFASTREFRESH   ; Identify that pixels drawn by fast-refresh are harder to clear
+  ;-DEINK_LIMIT_GHOSTING_PX=2000        ; (Optional) How much image ghosting is tolerated
+  ;-DEINK_BACKGROUND_USES_FAST          ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
+
+lib_deps =
+  ${esp32s3_base.lib_deps}
+  https://github.com/meshtastic/GxEPD2#b202ebfec6a4821e098cf7a625ba0f6f2400292d

variants/tlora_t3s3_epaper/variant.h

@@ -0,0 +1,69 @@
+#define HAS_SDCARD
+#define SDCARD_USE_SPI1
+
+// Display (E-Ink)
+#define USE_EINK
+#define PIN_EINK_CS 15
+#define PIN_EINK_BUSY 48
+#define PIN_EINK_DC 16
+#define PIN_EINK_RES 47
+#define PIN_EINK_SCLK 14
+#define PIN_EINK_MOSI 11
+
+#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to
+// measure battery voltage ratio of voltage divider = 2.0 (assumption)
+#define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
+#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
+
+#define I2C_SDA SDA
+#define I2C_SCL SCL
+
+// external qwiic connector
+#define GPS_RX_PIN 44
+#define GPS_TX_PIN 43
+
+#define LED_PIN 37
+#define BUTTON_PIN 0
+#define BUTTON_NEED_PULLUP
+
+// TTGO uses a common pinout for their SX1262 vs RF95 modules - both can be enabled and
+// we will probe at runtime for RF95 and if not found then probe for SX1262
+#define USE_RF95 // RFM95/SX127x
+#define USE_SX1262
+#define USE_SX1280
+
+#define LORA_SCK 5
+#define LORA_MISO 3
+#define LORA_MOSI 6
+#define LORA_CS 7
+#define LORA_RESET 8
+
+// per SX1276_Receive_Interrupt/utilities.h
+#define LORA_DIO0 9
+#define LORA_DIO1 33 // TCXO_EN ?
+#define LORA_DIO2 34
+#define LORA_RXEN 21
+#define LORA_TXEN 10
+
+// per SX1262_Receive_Interrupt/utilities.h
+#ifdef USE_SX1262
+#define SX126X_CS LORA_CS
+#define SX126X_DIO1 33
+#define SX126X_BUSY 34
+#define SX126X_RESET LORA_RESET
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+#endif
+
+// per SX128x_Receive_Interrupt/utilities.h
+#ifdef USE_SX1280
+#define SX128X_CS LORA_CS
+#define SX128X_DIO1 9
+#define SX128X_DIO2 33
+#define SX128X_DIO3 34
+#define SX128X_BUSY 36
+#define SX128X_RESET LORA_RESET
+#define SX128X_RXEN 21
+#define SX128X_TXEN 10
+#define SX128X_MAX_POWER 3
+#endif