Drobo-utils is a set of linux tools to query and manage Data Robotics Drobo storage systems. Fire up drobom view, and it should look familiar to those who have seen the dashboard on other operating systems. Drobom view is built on a little python programmer interface which can be installed on the system and used by other applications as well. For experienced Linux hands, the rest of the command line interface is provided by other sub-commands of drobom, and offer the same functionality as the view graphical interface.
Contents
- Compatibility Matrix
- COFFEE IS HOT
- INSTALLATION: Easiest
- Manual Setup Drobo with Linux
- Drobo Firmware
- Deployment
- Troubleshooting
- FAQ
- What LUNSIZE should I use?
- What Happens When I Used A Bigger LUNSIZE?
- How Do I Check That a LUNSIZE Works?
- Can I user ReiserFS, XFS, BTRFS, xxfs ?
- If my Drobo breaks, Can I Get My Data back?
- My USB Drobo always comes up as a different Disk!
- How come the command to build a file system builds an ext2 file system?
- Can you have different LUNS with different file systems on them?
- Does Drobo work with LVM?
- Does Drobo Support Full Disk Encryption?
- Does Drobo-Utiles work with USB3/ESATA
- Is it Still Supported ?
- I have read everything. Help?
- What is Drobo-utils' License?
- Credits
- Administrivia
If you can get your drobo device to be associated with a /dev/sdX [1] file, then you will be able to partition, build file systems and read & write data to it using ordinary system tools (see Setup.)
Drobo-utils accesses drobos via the same files. The software scans those files, and asking each device if it is a Drobo. Unfortunately, the way Drobos respond varies, so not all of them respond in a way that the software understands. Even for the same device, different physical interconnects may work with different functionality. There are two levels of access to Drobos: data (being able to read and write data, and full meaning that the drobo responds to the full command and control language.
With that in mind, the compatibility matrix of each device vs. the physical channel is below:
| Model | Interface ( Performance MB/s ) | Maximum LUN Size | ||||
| interf | USB | FW | TCP/IP | iSCSI | eSATA | ext3 |
| Drobo (Gen1) | full (15) | n/a (0) | n/a (0) | n/a (0) | n/a (0) | 2 |
| Drobo (Gen2) | full (15) | full? (?) | n/a (0) | n/a (0) | n/a (0) | 2 |
| Drobo Share | n/a (0) | n/a (0) | data*1 (15) | n/a (0) | n/a (0) | 2 |
| Drobo Pro | full (15) | ? (?) | n/a (0) | full*2 (80) | n/a (0) | 8 |
| Drobo Elite | ? (?) | n/a (0) | n/a (0) | ? (?) | n/a (0) | 8 |
|
full (15) | ? (?) | n/a (0) | n/a (?) | data (0) | 8 |
|
n/a (15) | n/a (?) | data (0) | n/a (?) | n/a (0) | 2? |
full - Find/Full: drobo-utils will find the device on it's own (auto-discover)
data - works: device functions for data i/o, but Drobo-utils cannot access it for configuration.
n/a - not applicable (device does not have this interface.)
*1 - Droboshare is not usable with drobo-utils on a linux server. If you
install Droboshare Augmented Root File System (DARFS_) then one can
run a drobo-utils in line mode on the droboshare itself.
*2 - Will not detect, out of the box, an iSCSI drobo. One must configure
the iSCSI subsystem to obtain a /dev/sdX file. see iSCSI Setup for
details on that initial configuration. After that point, Drobo-utils
will function properly over iSCSI.
| [1] | Linux drivers make disk, cdrom, and other peripherals, look like SCSI peripherals to applications. Regardless of the physical connection, it is a normal part of the linux kernel to make the device appear as a so-called "generic SCSI" one. |
People sued a national fast food chain because their coffee was hot, but did not have a warning on the cup stating that. For most people, the risk of scalding should be fairly obvious.
Drobo has made it so much easier to obtain much more secure storage, that some with little or no professional storage management experience are getting Drobos. Some have the expectation that Drobos, because they allow for disk failures, replace the need for backups. Sad stories have been told about people putting data only on the drobo, and no-where else, and then something happens and they lose the data.
You need to look at your data and determine the backup/data security strategy. If you have never done this, or do not know what it means, please consult the Deployment section in this page for examples.
On Ubuntu 9.10 [2] until Ubuntu 18.04 (or Debian unstable or other debian derived distributions), drobo-utils is included in the repositories, and installation from a shell prompt is simply:
% sudo apt-get install drobo-utils
to run at least the command line utility. Users on servers often want only command line functionality. On the other hand, to enable the graphical user interface, one more package must be installed:
% sudo apt-get install python-qt4
That is the easiest installation method, this method ensures that any packages required are automatically installed on the system as part of the above installation. On other distributions, or if the version in the repositories is too old, more complicated methods might be needed. For all other installation methods, one must ensure the packages that drobo-utils requires are installed. These packages are called Dependencies.
| [2] | Drobo-utils is developed for release on the stable version of Kubuntu at the time it is released. Development started on kubuntu 7.10 and continued to 9.10 at the end of 2009. Any similarly recent distribution ought to do. The package is accepted into Debian unstable, so all debian derived distributions (debian, *ubuntu, MEPIS, PCLinux-OS, etc...) should inherit the package in due course. |
later OS versions ship with python3. The dependencies for the current package are whatever seems current for a given OS. Nothing newish required. code just minimally ported to be functional on modern platform.
Before one can install drobo-utils itself, the other packages needed are something like those below (these examples are ubuntu packages, names may vary on other distributions):
python -- interpreter for python language parted -- partitioner, usually included with the distro.
If using Redhat Enterprise Linux (RHEL, aka. CentOS, Scientific Linux etc...), which have python 2.4 [3], then the following are necessary:
python-ctypes -- module for C-interface
| [3] | drobo-utils was tested in line mode using Python-2.4 for release 0.6.2.2. Prior to that there is a fairly scary bug, where it format wants to format all attached drives (only using 2.4) It was fixed for 0.6.2.2. |
The ctypes module is included with python3, so not necessary in that case.
On RPM-based distros (such as Redhat & SuSe), it would more likely be 'yum' instead of 'aptitude' and some of the package names will change. A typical difference is that packages for developers have the -devel suffix on Redhat derived distributions, instead of the -dev favoured by debian derived ones.
Here is an example from fedora 7 (courtesy of help4death on the google group):
% yum install python % yum install PyQt4 % yum install python-devel
NOTE: if X or QT is missing, it will only disable the GUI. Line mode will work without issues. The package should work fine on headless servers using only the command line.
If using python3 (from git) dependencies shift to python3-pyqt5.
Once dependencies are satisfied, one can install the latest stable package manually.
packages no longer built...
where the most current packages are available. after downloading a .deb, it is simply a matter of:
# dpkg -i drobo-utils-<version>.deb
done!
Redhat/Fedora users. alien may be used to convert the package. I don't know if it works. Someone to take on RPM packaging would be very welcome! This is a pure python package, so the chances are good that it does work without issue.
There is a Fedora Package
Assuming the dependencies are installed/satisfied, the package will actually run fine without being installed in any systemish places. Source code can be directly downloaded run it explicitly from the directory.
Point a browser at: <deprecated>
download the .tgz preferred, then unpack it:
# tar -xzvf drobo-utils-<version>.tgz # cd drobo-utils-<version> # ./drobom status
for all of the examples in the manual one just needs to prepend './' before drobom.
When a new model comes out, or the stable version is missing a feature, one may elect to follow along with the latest development version. installation of git, is necessary, then use it can be used to get a copy of the source tree:
# apt-get install git # git clone git://github.com/petersilva/drobo-utils # cd drobo-utils # ./drobom status # git pull
This gives a read-only copy of the source code that can be updated with the latest changes with 'git pull'. One can also select any stable version of drobo-utils by use of 'git branch -r', and 'git checkout'. For details, consult git documentation.
If you want a package, can build and install it:
# apt install debhelper dh-python # debuild -us -uc # dpkg -i ../drobo-utils-something.deb
So, one way or another, drobo-utils is installed. The next step is to try it out.
The first item to verify after installation is to invoke the command line interface (CLI.) and see if something sensible happens... on my system with a drobo[#sdz] the following happens:
% sudo drobom status /dev/sdz /drobo01 100% full ( ['Red alert', 'Bad disk', 'No redundancy'], 0 ) %
| [4] | in examples, drive always changed to sdz to avoid copy/paste errors. |
very scary, but my drobo is in bad shape right now... normal result is: [] as a status, which means there is nothing wrong. To get all kinds of information about the drobo, try 'drobom info.' Invocation without arguments at all which will cause it to print out a list of the commands available through the command line interface.
Once the command line functionality is verified, and assuming python-qt4 (umm... for python3, that would be python3-pyqt5 instead) is installed:
# drobom view
as root starts a GUI for each drobo attached to a computer. There are various tabs to allow one to obtain information from the Drobo, and also change its configuration. For example, one can use the Format tab of the GUI to partition the device and create a single file system for a given LUN.
There are two choices to make when setting up a Drobo: file system type, and LUN size. For a discussion of these choices, please consult: LUNSIZE fits all and Filesystem Choice.
This section provides an illustrative example of the most common configuration. An ext3 file system is built on a Drobo with whatever LUNSIZE is already in place. The GUI and line modes produce exactly the same result, and simply execute standard linux partitioning using parted, and the appropriate file system builder for the type in question. Sample CLI run:
PleaseEraseMyData# drobom -d /dev/sdz format ext3 peter@pepino:~/drobo/drobo-utils$ sudo ./drobom format ext3 /dev/sdz - Drobo disk pack 00% full - ([], 0) preparing a format script for a ext3 file system as you requested OK, I built the script but nothing is erased yet... You can have a look at it with: cat /tmp/fmtscript If you are really sure, go ahead and do: sh /tmp/fmtscript WARNING: Ready to destroy all your data. Continue? (y/n) n Phew... You stopped just in time! peter@pepino:~/drobo/drobo-utils$ # cat /tmp/fmtscript #!/bin/sh parted /dev/sdz mklabel gpt parted /dev/sdz mkpart pri ext3 0 100% parted /dev/sdz print; sleep 5 mke2fs -j -i 262144 -L Drobo01 -m 0 -O sparse_super,^resize_inode /dev/sdz1
The above sets up the drobo as one big partition, with a label that says it ought to contain an ext3[#mke3fs] file system. For an NTFS file system, write ´ntfs´ in place of ext3. The next step is to add the file system into the partition. while parted's are instantaneous, the mke2fs takes a while, just have a little patience, it´ll be fine. The ´coffee is hot´ disclaimer is necessary at this point:
WARNING: THE FOLLOWING LINES WILL ERASE ALL DATA ON YOUR DROBO! WARNING: NO, IT WILL NOT ASK ANY QUESTIONS! WARNING: ASK YOURSELF, before you start: ARE YOU SURE? WARNING: AFTER THE SECOND LINE, YOU ARE TOAST. WARNING: BEST TO BACKUP YOUR DATA BEFOREHAND... sh -x /tmp/fmtscript
(For an ntfs file system, use mkntfs -f -L Drobo01 /dev/sdz1 ... For ext3, be prepared to wait[#mkext3time]_ )
| [5] | The proper command to build an ext3 file system is mke2fs -j. This confuses people who wonder why one doesn't use some sort of ext3 mkfs. There isn't one, an ext3 is an ext2 with a journal. |
| [6] | mke2fs takes a very long time to run, on the order of ten minutes per Terabyte. the display format button just turns red while the format is in progress. Have not determined a method to monitor progress yet from the GUI yet. other file systems are much more quickly created, so less of an issue. |
Sample run:
root@alu:~# parted -i /dev/sdz
GNU Parted 1.7.1
Using /dev/sdz
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) mklabel gpt
(parted) mkpart pri ext2 0 100%
(parted) quit
root@alu:~# fdisk /dev/sdz
GNU Fdisk 1.0
Copyright (C) 1998 - 2006 Free Software Foundation, Inc.
This program is free software, covered by the GNU General Public License.
This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU General Public License for more details.
Using /dev/sdz
Command (m for help): p
Disk /dev/sdz: 2199 GB, 2199020382720 bytes
255 heads, 63 sectors/track, 267349 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdz1 1 267350 2147488843 83 Linux
Command (m for help): q
root@alu:~# mke2fs -j -i 262144 -L Drobo01 -m 0 -O sparse_super,^resize_inode /dev/sdz1
mke2fs 1.40.8 (13-Mar-2008)
Filesystem label=Drobo01
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
8388608 inodes, 536870886 blocks
0 blocks (0.00%) reserved for the super user
First data block=0
16384 block groups
32768 blocks per group, 32768 fragments per group
512 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968,
102400000, 214990848, 512000000
Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 26 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
root@alu:~#
root@alu:~# mount /dev/sdz1 /mnt
By default, Drobo creates a separate 'disk' visible to the computer for every 2 Terabytes (TiB) of parity-protected capacity on the unit. The natural usage that a drobo invites in users is to have a single, large device covering all the data on device. For example, on Mac OS/X, users often create 16 TB LUNS on HFS. This allows all the storage to fit on one large pool. The downside of larger LUNS has to do with startup time, and the time to perform a file system check.
Under Linux unfortunately, with a first generation Drobo, one should limit the volume size to 2 TiB[#gen12TiB]_. It is hoped, but not confirmed, that later products support LUNS larger than 2 TiB on Linux. Drobom view therefore limits lunsize to 2 TiB for the moment. The command line interface can be used to create larger LUNS, they just might not work.
- ON LUNSIZES >= 2TB:
- -- On older distributions, there are a couple of gotchas related to
- linux tools which aren't 2TB ready... to exceed 2 TB, you need to:
- -- use GPT partitions, which aren´t supported by older fdisk
- versions. Tools based on libparted work fine, mostly.
- -- gparted fails, and seems to have a 1 TB limit on devices.
- (bug #524948 reported to bugzilla.gnome.org) It's just the GUI, as libparted is fine, and other tools based on it still work.
- -- on linux kernel < 2.6.24, the USB layer won't let one address
- LUNs/offsets > 2 TB. For example, Ubuntu hardy (8.04) released in Spring 2008 has a 2.6.24, and so is OK. I've never been able to test this problem.
- -- On linux kernel < 2.6.31 there is are reported firewire problem that will
- prevent devices > 2 TiB from working.
- -- ext3 with 4K blocks is supposed to allow file system capacity of 8 TiB.
- 4K blocks seem to be assigned by default. So I think a good max. It would be fun to set the LunSIZE to 8 TiB and test it out...
-- Windows XP does not support LUNS > 2 TiB
| [7] | Many tests have been performed with first generation products and several different failure modes have been found when exceeding 2 TiB. Data Robotics has addressed several failure modes, via fixes to the kernel in 2.6.24, and for firewire in 2.6.31, and continues to address them in later generation products. |
Drobos work well under linux with ext3. One can, of course, set up an NTFS or HFS+ or FAT32 if necessary, but it seems actively counter-intuitive on Linux. Developers of Drobo-utils have not tested HFS. Linux does not write to Journalled HFS+ at this point, so HFS support is not present. Good success is reported with Ntfs-3g, but the performance is much lower than what is typically reported with ext3. Unless physical movement of the disk to between systems is required, the native (ext3) format is the best option.
This is a procedure for configuring a Drobo Pro for access via iSCSI. This information is based on a post by Lemonizer on the Google Group 2009/05/16, with updates based on improvements and tests by others in the fall of 2009:
1. Connect the Pro via USB, and manually configure the ip of the dbpro # drobom info settings # drobom set IPAddress 192.168.2.80 # drobom set NetMask 255.255.255.0 # drobom set UseStaticIPAddress True
The next step is to disconnect USB, and connect by iSCSI:
2. Install open-iscsi (http://www.open-iscsi.org/): sudo apt-get install open-iscsi 3. Connect the dbpro to host machine via iscsi 4. Query dbpro's id: sudo iscsiadm --mode discovery --type sendtargets --portal 192.168.2.80 5. Copy the id string returned by iscsiadm, something like "iqn.2005-06.com.datarobotics:drobopro.tdb091840080.node0" 6. Connect to the dbpro: sudo iscsiadm --mode node --targetname iqn.2005-06.com.datarobotics:drobopro.tdb091840080.node0 --portal 192.168.2.80:3260 --login
If everything went well, your drobopro should show up under /dev. Also check /var/log/messages to confirm that the iscsi device connected successfully. After that, drobo-utils should be able to detect the Drobo and manage it over ethernet/iSCSI.
(source: http://groups.google.com/group/drobo-talk/browse_frm/thread/453e02e105e9b41?hl=en )
Some people reported data corruption. This link claims to fix one such issue: http://www.drobospace.com/forum/thread/13951/Dropped-iSCSI-connections/?page=2#24792
Upgrading firmware is pretty self-explanatory in the GUI. the first time you press the Update button, it checks to see if a new firmware is available. If it there is newer firmware, it offer to upgrade, with suitable prompts. Similarly, the line mode interface has two commands to deal with firmware, fwcheck will tell you if an upgrade is required. the fwupgrade will do the job. It takes a few minutes, and prints a status you you can see how it is progressing. Have patience:
root@pepino:/home/peter/drobo/drobo-utils/trunk# drobom fwupgrade validateFirmware start... Magic number validated. Good. 484 + 2937552 = 2938036 length validated. Good. CRC from header: 4260378881, calculated using python zlib crc32: 398201869 yeah, the header CRCs do not match. For now they never do ... ignoring it. CRC for body from header: 1852877921, calculated: 1852877921 32 bit Cyclic Redundancy Check correct. Good. validateFirmware successful... writeFirmware: i=484, start=484, last=2938036 fw length= 488 . wrote 32768 bytes... total: 33252 wrote 32768 bytes... total: 66020 . . . wrote 32768 bytes... total: 2720228 wrote 32768 bytes... total: 2752996 wrote 32768 bytes... total: 2785764 wrote 32768 bytes... total: 2818532 wrote 32768 bytes... total: 2851300 wrote 32768 bytes... total: 2884068 wrote 32768 bytes... total: 2916836 wrote 21200 bytes... total: 2938036 writeFirmware Done. i=2938036, len=2938036 root@pepino:/home/peter/drobo/drobo-utils/trunk#
when it's done, check if it worked using:
root@pepino# drobom status /dev/sdf - 00% full - (['New firmware installed'], 0)
If the status is like that, then do:
root@pepino:/home/peter/drobo/drobo-utils/trunk# drobom shutdown
lights will flash etc... wait until Drobo goes dark. Wait another five seconds, then un-plug the USB / connector.
Plug it back in, and wait 10 seconds. it should start up with the latest firmware available for the drobo.
The drobom commands, like DRI's dashboard, will normally get the latest and greatest firmware and upgrade. If necessary one can load arbitrary firmware from the CLI with fwload command.
Those worried about safety of using this software should know: it was developed with assistance from the vendor (Data Robotics Inc.), and in every case, based on vendor documentation, and with at least encouragement, if not outright support. For each release, a QA.rst file is built, demonstrating the functionality tests run. There are multiple checksum verifications built into the firmware upgrade process, so it is next to impossible to brick a drobo using the tools. Drobo-utils verifies firmware checksums before attempting to upload the image to the device, and the device checks the firmware against the checksums as well. New firmware is loaded into an alternate location from the currently active one, and if activation of the new firmware fails, the drobo will simply boot the old one.
On the other hand, common sense rules do apply. Setting the LUN size, or re-formatting a Drobo will erase all data whether it is done on Linux or any other operating system. These are power tools, and they can do some damage data if used without proper care. For example, the reliability of any storage unit does not reduce the need for backups it only makes doing them easier. A Drobo is an excellent place to put backups, but not a substitute for them. Backups are the only way to address error 18 (the number of inches in front of the keyboard the source of the issue lies.) and no storage unit can protect against fire or flood.
Drobo has been tested with every old firmware version. Any Drobo should be upgradable to modern firmware using the dashboard.
for Drobo v1's (only models available to me used for QA)
- NOTE: really need at least 1.1.1 to use Linux & ext3.
- just use the tools to upgrade firmware ASAP.
- 1.01 - very old... bad idea to install this, need to write
- a script to get out, because it isn't in the revision table. not much works except firmware upgrade. DO NOT USE. UPGRADE ASAP
- 1.0.2 - works ok in CLI And GUI to view, and upgrade firmware.
- DO NOT USE. UPGRADE ASAP
- 1.0.3 - GUI and CLI work OK, can upgrade firmware.
- Used ntfs3g for a few months under ubuntu 7.10 Linux. Used 2 TB LUN, with 1.5 TB of physical space available. DO NOT USE. UPGRADE ASAP
- 1.1.0 - dashboard works no issues.
- from this point, you don't seem to need to unplug the USB connector to complete the upgrade.
- firmware prior to here deals badly with ext3.
- 1.1.1 - 1.2.4 works without issues.
- ('name' not supported by firmware)
1.3.0 - works without issues. 1.3.5 - works without issues.
No storage unit ever constructed, at any price point, can live upto the expectation of never losing data. There is no magic wand to wave to solve the data security problem. People still need a strategy around backups and their maintenance. Drobo makes it easier to implement a strategy, but does not replace it. Data Robotics has a best practices page that says it well, but the phrasing is a bit enterprisy, and while it provides general concepts, it is not prescriptive enough for people to easily apply.
This section gives some examples & use cases to help people develop the appropriate strategy for them. Try to keep it simple & concrete.
Don't rely on a single device, ever! Before deploying a storage unit, one should perform the thought experiment of what will happen if all data on it is lost. There are always levels of risk. For personal use, one might accept the risk that if the house burns down, only have infrequent offsite backups are available and months or years of data may be lost. If someone is running their business out of their home, this risk will likely not be acceptable.
The simplest method of backing up your data is to put it in a humungous single place, and backup the whole thing. That is a valid strategy, but consider the following realistic case:
A company does incremental backups[#incrbkup] once a day, and full backup once a week. Once a month, a second full backup is kept as monthly, while the weeklies are recycled. Monthly backups are kept for a year, and each year, one backup is kept for five years. So if you write data once and keep it unchanged for five years, you will have 3 weekly backups, 11 monthlies, and 4 yearly backups of that data, or 17 copies. This strategy is not unusual or particularly excessive, many corporate policies end up with 50 or more copies of the data.
With that in mind, if you avoid backing up what you don´t need to, then you are not saving just one byte, but all the copies too. With a little thought, one can usually reduce the total storage needs by classifying data appropriately.
| [8] | An incremental backup is where only what has changed since the last full backup is saved. a full backup is a complete copy of all data. |
Different Drobo models have very different performance. Deploying a Drobo using a USB interface as primary storage is likely to disappoint. See the compatibility matrix for details.
Classify Your Data
There are different levels of value for data. Things that are downloaded from the internet, or source code that is pushed to a repository on the internet, have natural backups in most cases. The loss of data being queued for printing, might not be a terrible loss. The loss of videos recorded off the air from television, might not be terrible either.
Any kind of data which is either not worth backing up, or for which a backups already exist, does not need to be backed up locally. The other end of the spectrum is proprietary data, for which copies on the internet are not be appropriate, and which is irreplaceable if lost. In a photographic business, the photos, Tax records, accounts, etc... In a personal realm, these would include family photos, etc... lets call this sort of information precious data
That irreplaceable data is what you need to safeguard. So the classification can be done in a number of ways, but the simplest is just to only put precious data in the home directory. So far that´s normal. The unusual thing comes next: Do not put anything else there. Internet downloads, easily replicable data, etc... should go somewhere else. In general, keep the home directories of users as small and precious as possible.
As another example, in my personal use case, Linux is readily downloadable, so there are no system backups at all. Configurations are relatively straightforward, only credentials, and special configurations are backed up, by having copies of the information in an normal /home directory of a user. The restoral time for a single system is not an issue for my personal use, and by the time a restore is necessary, there will probably a new OS version to try out, so the value of system backups is quite limited.
The only thing backed up, is the personal (/home) directories of a few users.
If a Drobo is used for primary storage for precious data, a second one should be obtained as a backup device. It´s as simple as that. Keeping all data on one device that cannot be backed up is asking for trouble.
Zealots will say that the second unit should be off-site. The Gen 1 / Gen 2 Drobo´s are also have limited performance, and are perhaps not well suited to a role as primary storage.
If the data there is all space that either exists elsewhere (mirrors of internet sites), can be regenerated (object files of compilation, recordings from on-air broadcasts in a media server), none of this data is particularly precious, and all of it can be recovered over time in the event of a data loss on one unit.
Again, one argument against such usage is performance. First and second generation units are a bit on the slow side for use in say. On the other hand, media serving is a streaming application with typically low instantaneous bandwidth requirements, so even first generation Drobos should be fine for that.
A rational means of configuring the Drobo is as a backup repository. The drobo is destination of the backups. Primary copies are on the desktops & laptops being backed up. Viewed in that way, backup data is easily recovered in the event of a data loss: just backup the system again. Of course the history of backups is lost, but the important thing is usually being able to recover current data.
To find Drobo on a system, drobo-utils queries all the attached devices for indications it is made by Data Robotics. These strings change from product to product. If the (new model) Drobo is not detected, then run the command line interface with the hardware detection debugging output turned out. like so:
# drobom -v 16 status examining: /dev/sda id: (0, 0, 0, 0, 'ATA ') rejected: vendor is ATA (not from DRI) examining: /dev/sdb id: (2, 0, 0, 0, 'ATA ') rejected: vendor is ATA (not from DRI) examining: /dev/sdc id: (8, 0, 0, 0, 'Drobo ') rejected: vendor is Drobo (not from DRI) returning list: [] No Drobos discovered
Here you see that the vendor string is 'Drobo' which was not a known vendor string at the time this example was run. so then try:
# drobom -s Drobo status
In other words, take the unknown vendor string and feed it as -s option to tweak detection of drobom. Your drobo will likely then be picked up.
LUN is an abbreviation of 'Logical UNit'. The origin of the term is SCSI[#SCSI]_ terminology. When RAID units became too large for support in the past, and were sub-divided to present smaller units the operating system. The default LUNSIZE on Drobos is 2 TiB (adjustable using the tools.) If more disk space (after allowing for parity/redundancy) than LUNSIZE is installed in a unit, Drobo will show a second (or even third) LUN. Each LUN shows up in Linux as a separate disk (examples if the first LUN shows up as /dev/sde, the next will be /dev/sdf, then /dev/sdg.)
If you think you should see multiple LUNS and you don't, you might have a look at some kernel settings: make sure that scsi_mod kernel module is loaded, make sure /sys/module/scsi_mod/parameters/max_luns is > 1.
Drobom view will start up one GUI per drobo, regardless of the number of LUNS. If asked to format, all LUNS for the device will be formatted.
| [9] | Small Computer System Interface. A ubiquitous standard for computers to communicate with storage hardware. SCSI includes hardware cabling specifications, which are mostly obsolete, but what remains is the "command set", the language used by the computer to make requests to the device. In that sense, All Drobos are SCSI devices. The SCSI commands are tunnelled within other protocols used to transport data between computer and device (Firewire, USB, eSATA, and, yes... ISCSI) |
DRI intends Drobospace.com for owners to talk with one another, except no non-owner can see the discussions, and early on, there was a lot of input from DRI staff, so it looked a lot like a support forum, but it really isn't. A lot of owners objected to these forums being private, so a google group was started for people to talk with one another, and the discussions to remain public:
http://groups.google.com/group/drobo-talk/topics?hl=en
There is still a great role for Drobo space, in that Tier 3 support analysts (essentially developers.) sometimes look over there. For tier 3 support, one cannot expect guaranteed response time, but one may be able to provide some input into future products or firmware features. It turns out that the Drobospace forums aren't really for support. but don't take my word for it, here is above was DRI's take (verbatim from a post on drobospace by MarkF 2008/08/29) on things:
To contact Data Robotics Inc. for support your options are:
- phone support - technical issues: 1-866-426-4280, Mon-Fri from 8am-5pm PST, excluding Holidays.
- phone support - presales questions: 1-866-99ROBOT
- email support - technical issues: [email protected]
- email support - presales questions: [email protected]
- web-based support request: http://www.drobo.com/Support/Request_Support.html
All technical support calls, emails, and web requests are assigned a case number and tracked. DRI has 3 tiers of customer support. Tier 1 and 2 handle the majority of cases. They are responsible for tracking phone, email, an web cases and resolving them. Some cases are escalated to Tier 3 whose personnel reside in our corporate headquarters and have access to engineering staff.
Support on Drobospace.com:
Drobospace.com is a user community and relies on the volunteer efforts of its members to help each other. Because it is run by volunteers response to problems varies. Tier 3 support personel monitor the Drobospace forums -- tiers 1 and 2 are focused directly on customers, and they are not required to read drobospace.com. By design Tier 3 personnel do not immediately respond to each posting in order to allow the community to function. Depending on the nature of the problem, tier 3 may post in the forum or contact the member directly through a private message to facilitate problem resolution.
Because Drobospace is owned and run by a third party, Capable Networks LLC, there is no linkage with DRI's database systems. Posts here are not assigned case numbers and tracked - that only happens with cases opened directly with DRI.
2 Terabytes is the biggest you should use for now. There are lots of experiments on the google groups, summarized here: LUNSIZE fits all Also consult the compatibility matrix indicates best guesses at the current state of affairs. DRI announced new firmware 1.1.4 for Drobo PRO which is supposed to remove the 2 TiB restriction, but that isn't confirmed yet.
That's actually a bit nasty. Nothing happens at first, everything seems to work fine. After a while, it fails to reclaim space when files are deleted. The blue capacity lights don't show much relation to how full the file system is, as reported by the operating system. Drobo may become insatiable, always asking for more and more disk space, even though the amount of data used on the file system doesn't warrant it. In extreme cases, data may become in-accessible.
DRI naturally releases new versions of firmware and may fix these issues at some point. If you are willing to test it out on your new Drobo, the procedure to do so is simple:
1. Create a file system as per normal. 2. Fill the physical space up. (blue lights should light up.) 3. Remove alot of the data.
If the problem is not there, then blue lights will function properly and go out to correspond to the deleted data after a while. If the blue lights do not go out after step 3, then do not trust your data to this file system. Re-create with a smaller LUN, and try again. 2 Terabytes is the only case of documented success so far.
Short answer: no.
For Drobo to perform storage management, it has to know what space is free, so it needs to understand the file system you are using. The list of file systems it official understands is: FAT32, NTFS, HFS+, ext3. That's it, so if you want to use reiserfs, or xfs, or GFS, or whatever... you are doing research. The vendors says those other file systems types will not work.
No. The way the data is placed on the disks is completely proprietary. You cannot take the drives and connect them individually to a server, and read the data off that way, because it isn't a linux md or lvm format that can easily be reconstructed. You cannot give the disk pack to a data recovery company, because they do not know the data format either, and you will have to pay them to reverse engineer DRI's format, which will get expensive quickly.
You need either a backup, or another Drobo. Even among Drobos there are limits to compatibility see the Drobo.com web site for details.
The order and timing of disks being connected to hot-plug busses will determine the device name (it might be /dev/sdb one time, and /dev/sdc another.) So putting /dev/sdX in the fstab to mount their disks, as is traditionally done, won't work. Instead, do:
peter@pepino:~$ ls -l /dev/disk/by-uuid total 0 lrwxrwxrwx 1 root root 10 2009-12-15 04:54 2C88743C8874071C -> ../../sda3 lrwxrwxrwx 1 root root 10 2009-12-15 04:54 32a41d0a-b193-41f3-86fa-29bbee8cd2b3 -> ../../sda8 lrwxrwxrwx 1 root root 10 2009-12-26 12:08 3cd5d9cc-c227-4ed8-bab2-60c2d71f6e9d -> ../../sdf1 lrwxrwxrwx 1 root root 10 2009-12-15 04:54 72b0ee8c-d0e8-479d-b79c-3dbda1581f55 -> ../../sda6 lrwxrwxrwx 1 root root 10 2009-12-15 04:54 814472db-dbee-411c-8870-7ca59f32e7c1 -> ../../sda5 lrwxrwxrwx 1 root root 10 2009-12-26 12:16 8ed93296-9be2-4576-9ae4-9d9c78363fb6 -> ../../sdg1 lrwxrwxrwx 1 root root 10 2009-12-15 04:54 a4bc252e-0eb7-489c-94e7-688efd528665 -> ../../sda7 lrwxrwxrwx 1 root root 10 2009-12-15 04:54 bc1ab400-df49-457d-8700-c77dde19e450 -> ../../sda2 lrwxrwxrwx 1 root root 10 2009-12-15 04:54 C2EE700DEE6FF7D5 -> ../../sda1 peter@pepino:~$
The UUID is a name that is constant for a partition. Each time a partition is mounted, a link will be created in this directory towards the correct /dev/sdX. A UUID related /etc/fstab entry looks like:
UUID=3cd5d9cc-c227-4ed8-bab2-60c2d71f6e9d /drobo01 ext3 defaults 0 2
because an ext3 file systems is an ext2 file system with a journal. The normal command to build an ext3 file system is mke2fs -j.
DRI: Multiple partitions per LUN is supported. Having any combination of file supported file systems on the different LUNS and partitions is fine as well.
Some people do it. I would not risk it.
The Linux Volume Manager is a layer of software which is shimmed between the file system layer, and the physical disks. It provides a 'fake' (virtual) volume on which file systems are built. This gives flexibility to concatenate several physical volumes together to make a single file system, or allocate a single volume to different file systems over time, as needs dictate rather than all at the outset.
For Drobo, LVM would be especially cool in that one could initially allocate only the physical space actually available within the LUN, and thus applications which key on avoiding filling file systems would function correctly, instead of always asking to insert more storage, and not managing the storage available. When more physical space (new drives!) becomes available, one could allocate more space to the virtual volume, and then grow the file system. So Drobo would still take care of the drudgery of RAID set maintenance, relay operations, etc... but the user would have more control on how space was allocated at the OS level.
For that to work, Drobo firmware would have to understand LVM to some extent. Initial experiments showed that the firmware didn't appreciate LVM. Being able to add a Drobo unit as an pv to an LVM unit would be very cool.
Drobo works by knowing how the file system is laid out and pretending to have more space than is physically present. Drobo does some sleight of hand to manage disk space and move things around optimally as hard disks fail or are added.
Full disk encryption implemented by the operating system makes the Drobo unable to understand the file system, so it doesn't know which blocks are in use, and the unit will always believe the system is completely full. Drobo will not behave well. Among the methods that will not work are any that operate on a raw disk partition, such as truecrypt, or any of the linux cryptoloop based solutions.
Instead of whole disk encryption, a method that uses an underlying file system that is well known to the Drobo (the list is short: FAT32, NTFS, HFS, EXT2) is needed. On windows, encrypting directories with standard NTFS will work fine. On Linux, a good choice would be EncFS http://www.arg0.net/encfs, which encrypts file names and data over an ext file system, or some other method which uses FUSE http://fuse.sourceforge.net. is reported to work well.
I no longer remember which one of these is totally pooched. At some point Drobo.com completely changed the protocol, so that it is completely differently done internally... The old one encapsulated generic SCSI packets inside USB. The new protocol is SATA based, and emulates SATA in USB. The original SCSI protocol support was built with help from Drobo.com, but the for new protocol, the vendor never published the format, so it would require full-on reverse engineering to get it to work.
Not really. I no longer have any hardware to test with, so cannot validate anything. I switched to QNAP instead, which was more appropriate for my needs. It lives on in the Debian archive because some kind soul is a maintainer there. If someone wants to take over, by all means git clone and go at it. I will provide whatever guidance I can to someone interested. I ported it to modern distros (python3/qt5/dh-python) so it fits in nicely with 20.04, but that broke things, so while it looks ok, there is some key broken stuff (diagnostics and firmware.)
Best first stop is the google Group_.
General Public License - Gnu - GPL .
who did what:
Peter Silva: wrote most all of it. Chris Atlee: the proper debian packaging. Brad Guillory: some help with diagnostics and patches. Joe Krahn: lots of inspiration. Andy Grover: some elegance cleanups. Sebastian Sobolewski: DroboPro patches, and testing.
Testers (of DroboPRO): robj, Sebastian (aka Tom Green), ElliotA, Andrew Chalaturnyk
version 9999, somewhen
copyright:
Drobo Utils Copyright (C) 2008,2009 Peter Silva ([email protected]) Drobo Utils comes with ABSOLUTELY NO WARRANTY; For details type see the file named COPYING in the root of the source directory tree.
