Update C6 Branch #5437
Closed
Update C6 Branch #5437
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Co-authored-by: thebentern <[email protected]>
…additional format validation. (#5084)
…new default interval one hour (#5086) * Coerce minimum telemetry interval of 30 minutes on defaults and make new default interval one hour * Smaller log messages
Triple Press on buttons toggles GPS enable/disable. This enhancement plays a triple-beep so that users of devices with buzzers can get audible feedback about whether they have turned the GPS off or on. This is especially valuable for screenless devices such as the T1000E where it may not be immediately obvious the GPS has been disabled.
Co-authored-by: thebentern <[email protected]>
Revert "Permanently engage !CTRL"
…dule (#5087) * Initial NODENUM_BROADCAST_NO_LORA implementation with NeighborInfo module * isBroadcast * Trunkt
* Move 115200 baud GNSS probe earlier * Even more optimized!
After the recent change to move logging line breaks to a central location, GPS_DEBUG is now emitting one character per line, making the logs unusable. Patch uses local strings and appends to collate and then print in the right places. Fixes #5099 Co-authored-by: Ben Meadors <[email protected]>
Wide_Lora uses 12 symbols to be compatible with SX1280
Implements an input driver utilising the MPR121 Touch IC and is compatible with common MPR121 keypad PCB's. - Implements a "candybar" phone style 12-key keypad - multiple taps to rotate through the character set - longpress for navigation keys - keymap to allow arbitrary routing of MPR121 pin to button configuration - extendable to other key functions - Integrates with the existing kbI2cBase implementation - Works with CannedMessageModule Freetext mode - Can be used with common MPR121 boards, such as https://www.amazon.com/MPR121-Capacitive-Keyboard-Buttons-Sensitive/dp/B083R89CHB/ref=sr_1_6 - Of use for PCB based radios, where some form of low surface area low component freetext input is required, but also without consuming too many IO pins. - Tested on a T3S3 connected to Wire1 (Second) interface. - Demonstration of functionality: https://youtu.be/UI6QP6nGvhY
Add the RFC 3927 IP address block (169.254.0.0/16), also referred to as IPIPA, to the private address checks for MQTT functionality.
Co-authored-by: thebentern <[email protected]>
Adding restart on service failure with 3 seconds between restart to stop fasst restart loops. Adding StartLimitBurst to limit it to 5 restarts in 200 seconds.
* Add device unique id * Trunk * WIP * Esp32 implementation * Trunk * Check for ESP_EFUSE_OPTIONAL_UNIQUE_ID * Comment print * Trunk
Co-authored-by: thebentern <[email protected]>
* T1000-E Peripherals - enable intelligent charge controller signals - enable Accelerometer - enable internal I2C bus - provide Power to Accelerometer * POC Accelerometer Code (wakeScreen is moot for that device, just test if the driver works) * fix building without the sensor
This was shuffled around a couple years ago, but hasn't been used since, and we had two copies in the code. Delete it.
RedirectablePrint had a method, getLogLevel, which did exactly what code in SerialConsole did. Let's use that method rather than duplicating the code.
Co-authored-by: thebentern <[email protected]>
Co-authored-by: thebentern <[email protected]>
* add smiley emoji * clang-formatted
Co-authored-by: thebentern <[email protected]>
This avoids hitting the 404 Not Found handler, which breaks connection keep-alive, so this change fixes a big performance regression for Web Client in Chrome: #5385 Tested on Heltec V3. Co-authored-by: Ben Meadors <[email protected]>
* Create a specific hw_model for WisMesh Tap * Trunk * HAS_ETHERNET * Remove it altogether * Don't need these either
* Fix RTC time injection and consolidate position logic * Comment out unused var warning * Backerds
* Update arduino-pico core to fix sporadic hangs * Update platform-raspberrypi also
* Add --web * Update device-install.bat Forgot a "-" a few places. --------- Co-authored-by: Ben Meadors <[email protected]>
…all of the nodes (#5412)
* Add --web * Update device-install.bat Forgot a "-" a few places. * Typo fix. * Typo fix --------- Co-authored-by: Ben Meadors <[email protected]> Co-authored-by: GUVWAF <[email protected]>
Leads to a panic
* Check for oktomqtt flag presence before uplinking to MQTT * Move to mqtt->onSend
* Try-fix (workaround) T-Deck audio crash * set T-Deck audio to unused 48 (mem mclk) * swap mclk to gpio 21 * dreamcatcher: assign GPIO44 to audio mclk --------- Co-authored-by: mverch67 <[email protected]>
* add canned message and keyboard in indicator board * Added virtual keyboard macro and enabled for Indicator * Cleanup macros by applying USE_VIRTUAL_KEYBOARD and DISPLAY_CLOCK_FRAME --------- Co-authored-by: Ben Meadors <[email protected]>
* Update build-native.sh Device-install.sh and device-update.sh are not used on native platform, skip copying to release directory after build and copy native-install.sh and native-run.sh instead. * Update build-native.sh Skip native-run.sh copy
Signed-off-by: Christopher Hoover <[email protected]>
* Fix LED pinout for T-Echo board marked v1.0, date 2021-6-28 * Merge PR #420 * Fixed double and missing Default class. * Use correct format specifier and fixed typo. * Removed duplicate code. * Fix error: #if with no expression * Fix warning: extra tokens at end of #endif directive. * Fix antenna switching logic. Complementary-pin control logic is required on the rp2040-lora board. * Fix deprecated macros. * Set RP2040 in dormant mode when deep sleep is triggered. * Fix array out of bounds read. * Admin key count needs to be set otherwise the key will be zero loaded after reset. * Don't reset the admin key size when loading defaults. Preserve an existing key in config if possible. * Remove log spam when reading INA voltage sensor. * Remove static declaration for admin keys from userPrefs.h. Load hard coded admin keys in case config file has empty slots. * Removed newlines from log. --------- Co-authored-by: Ben Meadors <[email protected]> Co-authored-by: Thomas Göttgens <[email protected]>
* Remove BMA-423 by default * STK * Wrong macro * Helps if you include the file
Co-authored-by: caveman99 <[email protected]>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
No description provided.